02-02-2010
Hi Pludi,
Thanks, you're right, ifconfig -a shows somthing different:
I had a eth2_rename directive somewhere, went to modify /etc/udev/rules.d/70-persistent-net.rules and it all works fine now.
Thank you very much!
Santiago
10 More Discussions You Might Find Interesting
1. IP Networking
I have a UnixWare 2 server that has an ISA 3Com NIC that has just a BNC connector on it. I want to remove this and install an ISA 3Com NIC that has a BNC/RJ45 connector. What steps do I have to go through to successfully complete this? Thye are almost the exact same cards except for the... (1 Reply)
Discussion started by: cparks
1 Replies
2. UNIX for Advanced & Expert Users
I have been having trouble with my sis900 neytwork card in slacwkare linux. I tried to modprobe the sis900, it didnt give me any errors but it didnt load it. so I put in a realtek 8139 network card and tried it too. These are the errors i get with the two cards when trying to do insmod on either of... (3 Replies)
Discussion started by: The Fridgerator
3 Replies
3. UNIX for Advanced & Expert Users
hi, everyone:
alpha 600 au true64 Unix 4.0f
my network cart is set "Auto-Negotiate".After operate system startup,the network will be disconnected by itself at sometime. I found some prompt in /usr/adm/messages.
"tu0 :transmit FIFO underflow:threshold raised to :256 byteŁ¬link up... (1 Reply)
Discussion started by: q30
1 Replies
4. UNIX for Dummies Questions & Answers
Hi!.
I have problems installing my network card under
ther redhat kernel.
First i tryed my integrated intel pro set 10/100
then my d-link 530tx Pci but none of them seems to
be found.
also i huse my network card to connect to the net
trough PPPOE where i need to type my username and... (3 Replies)
Discussion started by: Gibbler
3 Replies
5. Solaris
Hi,
After I installed Solaris 10 in the Intel platform (chipset 865*) network card was not detected, were shall I get this driver? iam new to Solaris. (2 Replies)
Discussion started by: pravin_2929
2 Replies
6. Debian
I've had no luck with help on linuxquestions so I figured I'd try here. I'm using debian etch.
The problem is that I can not install my network card because it says:
Makefile:62: *** Linux kernel source not found. Stop.
I have the kernel-headers installed.
I've looked all over the... (9 Replies)
Discussion started by: Virtuality
9 Replies
7. UNIX for Dummies Questions & Answers
I have three network cards in my unix box. I need to figure out which card corresponds to an assigned IP address. If there some command in unix I can use to make an ethernet interface blink?
Any advice would be appreciated. (6 Replies)
Discussion started by: mojoman
6 Replies
8. Solaris
Hi Experts,
Can we use some command from unix to find the available network interface? I did tried
Its listing following, however how can I decide the which vender card is attached
e.g. if its hme , bge or some thing else
Thanks (7 Replies)
Discussion started by: kumarmani
7 Replies
9. Red Hat
Dear All ,
While taking backups in one Linux Server , we find one alert came with regard to Network Interface Card.
Pl find the below alert.
Network Interface Card performance for NIC:eth1 has exceeded Major threshold.
Bytes sent and received per second (Average)= 105540.303101... (6 Replies)
Discussion started by: jegaraman
6 Replies
10. Ubuntu
Hi
Please can you help me to understand what could be wrong based on what I have captured in the logs:
I have run cat /var/log/syslog | grep -i warn, and I got the following output NetworkManager: <warn> Activation (eth3) failed.
Dec 23 10:58:25 cmoveldb02 NetworkManager: <warn> (eth3): DHCPv4... (2 Replies)
Discussion started by: fretagi
2 Replies
LEARN ABOUT DEBIAN
sinfod
SINFOD(8) User Manuals SINFOD(8)
NAME
sinfod - a monitoring tool for networked computers
SYNOPSIS
sinfod [-F] [-q] [-V] [-b #.#.#.#] [-c] [-n card ] [ -N nicevalue ] [ -m marker ] [ -i processname ] [-s][-W]
DESCRIPTION
sinfod distributes system information to other sinfods on your local network.
These Information include the system load, memory utilization and the `TOP-5' processes on every machine.
It's main advantage is, that these informations are broadcasted using the udp(7) protocol.
If each node broadcasts it's information in a cooperative manner, the network load is O(N), where N is the number of nodes in your network.
Other systems to monitor your cluster load (e.g. rup(1) ) are using a polling scheme where every node has to ask every other node for the
system information: In that case the network load is O(N**2).
The task of sinfod is to broadcast the relevant information for the local node and to collect broadcasts from other nodes. Other programs
( sinfo(1) ) can get access to this information via a simple tcp(7) connection that normally is routed through the local loopback inter-
face.
OPTIONS
-F/--foreground
Unlike normal operation, sinfod will not detach from the terminal when given this option. Some debugging informations will be visi-
ble.
-q/--quiet
Start quietly - for init scripts.
-V/--version
Print the version number and exit.
-b #.#.#.#/--bcastaddress=#.#.#.#
Set the broadcast address of the sinfod. Default is 255.255.255.255. In you want to run sinfod without a network card "-b
127.0.0.1" may be necessary.
-c/--cmdline
Broadcast the full command line of a process instead of the command only.
-m marker/--marker=marker
Mark the machine with a name. e.g. laboratory, pool or cluster.
-i/--ignore <process>
Don't broadcast any information on <process> ; --ignore may be set multiple times.
-t/--top <count>
Broadcast information on the top <count> processes; default: 5
-n card/--networkcard=card
Set the name of the network card whose informations will be broadcasted. (e.g. eth0). Default is the network card that saw the most
traffic at the start of sinfod.
-N nicevalue/--nice=nicevalue
Set the priority of this demon to nicevalue. Default is 15.
-s/--spymode
Deactivate the TCP interface and the collection of received packets. The demon starts in a broadcast-only mode.
-W/--watchdog
Start with simple watchdog.
AUTHOR
Juergen Rinas <jrinas@gmx.de>
SEE ALSO
sinfo(1),sshallsinfo(1),
Linux JANUARY 2005 SINFOD(8)