02-02-2010
ifconfig, by default, shows only configured cards (those with an address). ifconfig -a will show all.
10 More Discussions You Might Find Interesting
1. IP Networking
I have a UnixWare 2 server that has an ISA 3Com NIC that has just a BNC connector on it. I want to remove this and install an ISA 3Com NIC that has a BNC/RJ45 connector. What steps do I have to go through to successfully complete this? Thye are almost the exact same cards except for the... (1 Reply)
Discussion started by: cparks
1 Replies
2. UNIX for Advanced & Expert Users
I have been having trouble with my sis900 neytwork card in slacwkare linux. I tried to modprobe the sis900, it didnt give me any errors but it didnt load it. so I put in a realtek 8139 network card and tried it too. These are the errors i get with the two cards when trying to do insmod on either of... (3 Replies)
Discussion started by: The Fridgerator
3 Replies
3. UNIX for Advanced & Expert Users
hi, everyone:
alpha 600 au true64 Unix 4.0f
my network cart is set "Auto-Negotiate".After operate system startup,the network will be disconnected by itself at sometime. I found some prompt in /usr/adm/messages.
"tu0 :transmit FIFO underflow:threshold raised to :256 byteŁ¬link up... (1 Reply)
Discussion started by: q30
1 Replies
4. UNIX for Dummies Questions & Answers
Hi!.
I have problems installing my network card under
ther redhat kernel.
First i tryed my integrated intel pro set 10/100
then my d-link 530tx Pci but none of them seems to
be found.
also i huse my network card to connect to the net
trough PPPOE where i need to type my username and... (3 Replies)
Discussion started by: Gibbler
3 Replies
5. Solaris
Hi,
After I installed Solaris 10 in the Intel platform (chipset 865*) network card was not detected, were shall I get this driver? iam new to Solaris. (2 Replies)
Discussion started by: pravin_2929
2 Replies
6. Debian
I've had no luck with help on linuxquestions so I figured I'd try here. I'm using debian etch.
The problem is that I can not install my network card because it says:
Makefile:62: *** Linux kernel source not found. Stop.
I have the kernel-headers installed.
I've looked all over the... (9 Replies)
Discussion started by: Virtuality
9 Replies
7. UNIX for Dummies Questions & Answers
I have three network cards in my unix box. I need to figure out which card corresponds to an assigned IP address. If there some command in unix I can use to make an ethernet interface blink?
Any advice would be appreciated. (6 Replies)
Discussion started by: mojoman
6 Replies
8. Solaris
Hi Experts,
Can we use some command from unix to find the available network interface? I did tried
Its listing following, however how can I decide the which vender card is attached
e.g. if its hme , bge or some thing else
Thanks (7 Replies)
Discussion started by: kumarmani
7 Replies
9. Red Hat
Dear All ,
While taking backups in one Linux Server , we find one alert came with regard to Network Interface Card.
Pl find the below alert.
Network Interface Card performance for NIC:eth1 has exceeded Major threshold.
Bytes sent and received per second (Average)= 105540.303101... (6 Replies)
Discussion started by: jegaraman
6 Replies
10. Ubuntu
Hi
Please can you help me to understand what could be wrong based on what I have captured in the logs:
I have run cat /var/log/syslog | grep -i warn, and I got the following output NetworkManager: <warn> Activation (eth3) failed.
Dec 23 10:58:25 cmoveldb02 NetworkManager: <warn> (eth3): DHCPv4... (2 Replies)
Discussion started by: fretagi
2 Replies
LEARN ABOUT DEBIAN
ocsinventory::agent::common
Ocsinventory::Agent::Common(3pm) User Contributed Perl Documentation Ocsinventory::Agent::Common(3pm)
addController()
Add a controller in the inventory.
addModem()
Add a modem in the inventory.
addDrive()
Add a partition in the inventory.
addStorages()
Add a storage system (hard drive, USB key, SAN volume, etc) in the inventory.
addMemory()
Add a memory module in the inventory.
addPort()
Add a port module in the inventory.
addSlot()
Add a slot in the inventory.
addSoftware()
Register a software in the inventory.
addMonitor()
Add a monitor (screen) in the inventory.
addVideo()
Add a video card in the inventory.
addSound()
Add a sound card in the inventory.
addNetwork()
Register a network in the inventory.
setHardware()
Save global information regarding the machine.
The use of setHardware() to update USERID and PROCESSOR* informations is deprecated, please, use addUser() and addCPU() instead.
setBios()
Set BIOS informations.
addCPU()
Add a CPU in the inventory.
addUser()
Add an user in the list of logged user.
addPrinter()
Add a printer in the inventory.
addVirtualMachine()
Add a Virtual Machine in the inventory.
addProcess()
Record a running process in the inventory.
addIpDiscoverEntry()
IpDiscover is used to identify network interface on the local network. This is done on the ARP level.
This function adds a network interface in the inventory.
setAccessLog()
What is that for? :)
flushXMlTags()
Clear the content of $common->{xmltags} (to use after adding it in XML)
POD ERRORS
Hey! The above document had some coding errors, which are explained below:
Around line 34:
'=item' outside of any '=over'
perl v5.14.2 2012-04-12 Ocsinventory::Agent::Common(3pm)