02-02-2010
ifconfig, by default, shows only configured cards (those with an address). ifconfig -a will show all.
10 More Discussions You Might Find Interesting
1. IP Networking
I have a UnixWare 2 server that has an ISA 3Com NIC that has just a BNC connector on it. I want to remove this and install an ISA 3Com NIC that has a BNC/RJ45 connector. What steps do I have to go through to successfully complete this? Thye are almost the exact same cards except for the... (1 Reply)
Discussion started by: cparks
1 Replies
2. UNIX for Advanced & Expert Users
I have been having trouble with my sis900 neytwork card in slacwkare linux. I tried to modprobe the sis900, it didnt give me any errors but it didnt load it. so I put in a realtek 8139 network card and tried it too. These are the errors i get with the two cards when trying to do insmod on either of... (3 Replies)
Discussion started by: The Fridgerator
3 Replies
3. UNIX for Advanced & Expert Users
hi, everyone:
alpha 600 au true64 Unix 4.0f
my network cart is set "Auto-Negotiate".After operate system startup,the network will be disconnected by itself at sometime. I found some prompt in /usr/adm/messages.
"tu0 :transmit FIFO underflow:threshold raised to :256 byteŁ¬link up... (1 Reply)
Discussion started by: q30
1 Replies
4. UNIX for Dummies Questions & Answers
Hi!.
I have problems installing my network card under
ther redhat kernel.
First i tryed my integrated intel pro set 10/100
then my d-link 530tx Pci but none of them seems to
be found.
also i huse my network card to connect to the net
trough PPPOE where i need to type my username and... (3 Replies)
Discussion started by: Gibbler
3 Replies
5. Solaris
Hi,
After I installed Solaris 10 in the Intel platform (chipset 865*) network card was not detected, were shall I get this driver? iam new to Solaris. (2 Replies)
Discussion started by: pravin_2929
2 Replies
6. Debian
I've had no luck with help on linuxquestions so I figured I'd try here. I'm using debian etch.
The problem is that I can not install my network card because it says:
Makefile:62: *** Linux kernel source not found. Stop.
I have the kernel-headers installed.
I've looked all over the... (9 Replies)
Discussion started by: Virtuality
9 Replies
7. UNIX for Dummies Questions & Answers
I have three network cards in my unix box. I need to figure out which card corresponds to an assigned IP address. If there some command in unix I can use to make an ethernet interface blink?
Any advice would be appreciated. (6 Replies)
Discussion started by: mojoman
6 Replies
8. Solaris
Hi Experts,
Can we use some command from unix to find the available network interface? I did tried
Its listing following, however how can I decide the which vender card is attached
e.g. if its hme , bge or some thing else
Thanks (7 Replies)
Discussion started by: kumarmani
7 Replies
9. Red Hat
Dear All ,
While taking backups in one Linux Server , we find one alert came with regard to Network Interface Card.
Pl find the below alert.
Network Interface Card performance for NIC:eth1 has exceeded Major threshold.
Bytes sent and received per second (Average)= 105540.303101... (6 Replies)
Discussion started by: jegaraman
6 Replies
10. Ubuntu
Hi
Please can you help me to understand what could be wrong based on what I have captured in the logs:
I have run cat /var/log/syslog | grep -i warn, and I got the following output NetworkManager: <warn> Activation (eth3) failed.
Dec 23 10:58:25 cmoveldb02 NetworkManager: <warn> (eth3): DHCPv4... (2 Replies)
Discussion started by: fretagi
2 Replies
LEARN ABOUT SUNOS
scf_card_reset
SCF_Card_reset(3SMARTCARD) Smartcard Library Functions SCF_Card_reset(3SMARTCARD)
NAME
SCF_Card_reset - perform a reset of a smartcard
SYNOPSIS
cc [ flag... ] file... -lsmartcard [ library...]
#include <smartcard/scf.h>
SCF_Status_t SCF_Card_reset(SCF_Card_t card);
PARAMETERS
card The card (from SCF_Terminal_getCard(3SMARTCARD)) to be reset
DESCRIPTION
The SCF_Card_reset() function causes the specified smartcard to be reset by the terminal.
A card can be reset only if it has not been locked (with SCF_Card_lock(3SMARTCARD)) by another client. A client wishing to reset a card
should either first call SCF_Card_lock() to obtain the card lock, or be prepared to retry the reset operation if it fails because another
client holds the card lock.
When the card is reset, any SCF_Card_t object representing the card will continue to remain valid after the reset. When the reset occurs,
an SCF_EVENT_CARDRESET event will be sent to all registered event listeners for the terminal (assuming they registered for this event).
This is the only notification of a reset provided to SCF clients. When a client receives this event, it should be prepared to reinitialize
any state on the card that might have been interrupted by the reset. New information about the card (for example, ATR, if it changed) can
also be available from SCF_Card_getInfo(3SMARTCARD).
RETURN VALUES
If the card is successfully reset, SCF_STATUS_SUCCESS is returned. Otherwise, the status of the card remains unchanged and an error value
is returned.
ERRORS
The SCF_Card_reset() function will fail if:
SCF_STATUS_BADHANDLE The specified card has been closed or is invalid.
SCF_STATUS_CARDLOCKED The card cannot be reset because another client holds a lock on the card.
SCF_STATUS_CARDREMOVED The card cannot be reset because the card represented by the SCF_Card_t has been removed.
SCF_STATUS_COMMERROR The connection to the server was lost.
SCF_STATUS_FAILED An internal error occured.
EXAMPLES
Example 1: Reset a card.
SCF_Status_t status;
SCF_Card_t myCard;
/* (...call SCF_Terminal_getCard to open myCard...) */
status = SCF_Card_lock(myCard, SCF_TIMEOUT_MAX);
if (status != SCF_STATUS_SUCCESS) exit(1);
status = SCF_Card_reset(myCard);
if (status != SCF_STATUS_SUCCESS) exit(1);
status = SCF_Card_unlock(myCard);
if (status != SCF_STATUS_SUCCESS) exit(1);
/* ... */
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Interface Stability |Evolving |
+-----------------------------+-----------------------------+
|MT-Level |MT-Safe |
+-----------------------------+-----------------------------+
SEE ALSO
libsmartcard(3LIB), SCF_Card_getInfo(3SMARTCARD), SCF_Card_lock(3SMARTCARD), SCF_Terminal_addEventListener(3SMARTCARD), SCF_Terminal_get-
Card(3SMARTCARD), attributes(5)
SunOS 5.10 28 Feb 2001 SCF_Card_reset(3SMARTCARD)