02-01-2010
This isn't a best post to get fast answer. Please put some commands, system responses etc. .
Do you try using any command and get some error ? Generally I don't think you'd have to destroy zpool to remove a storage device from it.
10 More Discussions You Might Find Interesting
1. Solaris
I had a pool which was exported and due to some issues on my SAN i was never able to import it again. Can anyone tell me how can i destroy the exported pool to free up the LUN. I tried to create a new pool on the same pool but it gives me following error
# zpool create emcpool4 emcpower0c... (0 Replies)
Discussion started by: fugitive
0 Replies
2. Solaris
I have a list of LUN ID, my task is to find if disk has been added or not. How do I do that? I have been searching the forum and not able to find answer.
thanks (4 Replies)
Discussion started by: uuontario
4 Replies
3. Solaris
hi ...
i have added a physical disk to the pool with
""zpool add <poolname> diskname"""... after that i realized that i have to mirror it instead..then i tried to take that disk out of the pool but i m not able to do that..
i have gone through many unix help sites , nothing worked ,
so please... (6 Replies)
Discussion started by: yrajendergoud
6 Replies
4. UNIX for Advanced & Expert Users
Hi,
How to remove the allocate SAN Lun on the Linux Server. I am using rhel 5.8. I have assigned a LUN to the existing Volume group.
For eg: I have allocated a LUN with 20GB to the existing volume group(test123). Now, how can I take back the allocated lun without any issues. (1 Reply)
Discussion started by: gsiva
1 Replies
5. Solaris
Hi ,
One of my zone went down and when i booted it up i could see the pool in degraded state with some check sum errors . we have brought the pool online after scrubbing. But few files are showing this error
Bad exchange descriptor
Please let me know how to remove these files (2 Replies)
Discussion started by: chidori
2 Replies
6. Solaris
So, we removed a LUN from the SAN and the system is refusing to remove the references to it in the /dev folder. I've done the following:
devfsadm -Cv
powermt -q
luxadm -e offline <drive path>
luxadm probe
All those commands failed to remove the path. The drive stills shows up as <drive... (13 Replies)
Discussion started by: DustinT
13 Replies
7. Solaris
I added a disk to a zpool using "zpool add diskname"
My intention was mirror a zpool disk that no mirror; that is a zpool with only one disk. I did not issue the right command. Now, the disk has been added successfully but I cannot remove nor detach it as Solaris 11 thinks it has data on it... (14 Replies)
Discussion started by: LittleLebowski
14 Replies
8. Solaris
So,
We have a Netapp storage solution. We have Sparc T4-4s running with LDOMS and client zones in the LDOMS, We are using FC for storage comms. So here's the basic setup
FC luns are exported to the primary on the Sparc box. using LDM they are then exported to the LDOM using vdisk. at the... (4 Replies)
Discussion started by: os2mac
4 Replies
9. Solaris
Hi all, I have a LUN that is in "Online Busy" when I issue the dev_gestate subcommand of luxadm:
root@es088wb6:~# luxadm -v -e dev_getstate /dev/rdsk/c21t50050763090887FEd4s2
phys path = "/devices/pci@6c0/pci@1/pci@0/pci@4/SUNW,qlc@0/fp@0,0/ssd@w50050763090887fe,4:c,raw"
... (5 Replies)
Discussion started by: ludiegu
5 Replies
10. Solaris
Now this doesnt look right to me. All of these disks are 100Gb LUNS so total zpool size is 300Gb.
Am I right in saying that this zpool consists of two disks plus one more disk that is 6 way mirrored?
So a bit pointless because only one of the three is mirrored (and 6 way is a bit of overkill... (3 Replies)
Discussion started by: psychocandy
3 Replies
LEARN ABOUT FREEBSD
zfsloader
ZFSLOADER(8) BSD System Manager's Manual ZFSLOADER(8)
NAME
zfsloader -- kernel bootstrapping final stage
DESCRIPTION
zfsloader is an extended variant of loader(8) with added support for booting from ZFS. This document describes only differences from
loader(8).
ZFS FEATURES
zfsloader supports the following format for specifying ZFS filesystems which can be used wherever loader(8) refers to a device specification:
zfs:pool/filesystem:
where pool/filesystem is a ZFS filesystem name as described in zfs(8).
If /etc/fstab does not have an entry for the root filesystem and vfs.root.mountfrom is not set, but currdev refers to a ZFS filesystem, then
zfsloader will instruct kernel to use that filesystem as the root filesystem.
ZFS COMMAND EXTENSIONS
lsdev [-v]
Lists ZFS pools in addition to disks and partitions. Adding -v shows more ZFS pool details in a format that resembles zpool status
output.
lszfs filesystem
A ZFS extended command that can be used to explore the ZFS filesystem hierarchy in a pool. Lists the immediate children of the
filesystem. The filesystem hierarchy is rooted at a filesystem with the same name as the pool.
FILES
/boot/zfsloader zfsloader itself.
EXAMPLES
Set the default device used for loading a kernel from a ZFS filesystem:
set currdev=zfs:tank/ROOT/knowngood:
SEE ALSO
gptzfsboot(8), loader(8), zfs(8), zfsboot(8), zfsloader(8), zpool(8)
HISTORY
The zfsloader first appeared in FreeBSD 7.3.
AUTHORS
This manual page was written by Andriy Gapon <avg@FreeBSD.org>.
BSD
September 15, 2014 BSD