vsftpd can be set up either as a standalone service or as an on demand service. You have set it up as an on demand service but failed to comment out the LISTEN=Yes directive in /etc/vsftpd/vsftpd.conf.
Code:
# When "listen" directive is enabled, vsftpd runs in standalone mode and
# listens on IPv4 sockets. This directive cannot be used in conjunction
# with the listen_ipv6 directive.
listen=YES
Hello,
I have two problems:
1. The service command does not work on my system! I mean when I enter:
service ... start
I get: bash: service: command not found
2. I want to launch my vsftpd server. I tried to launch it using service command and you see that it didn't work!
Please help... (1 Reply)
I have a Solaris-9 box. When I log into it I get the following error message
tmchild exec service failed erron = 2 . Any ideas !!
Thanks Mike (2 Replies)
I recently installed SLES 10 on an x86 64bit blade server. I then installed vsftpd from the suse cds through network services; however after configuring the vsftpd.conf file, the server fails to start:
# /etc/init.d/vsftpd start
Starting vsftpd startproc: exit status of parent of... (5 Replies)
Hi Guys,
I have requirement where if the script fails at a particular point, then the script should run from that particular point itslf..
could anyone help me out from this..
Thanks (5 Replies)
My apache and ftp server is working fine but when I reboot the system ftp and web server is not running automatically. Please advise on how to start apache and ftp at boot. (9 Replies)
As topic, assume we have a service called "blahservice"
and we can start it by:
startsrc -s blahservice
what is the best practice to run such command when system start?
- directly use mkitab to add it into /etc/inittab
or
- drop startup scripts in /etc/rc.d/rcX.d
I know they... (4 Replies)
Today I have installed VSFTPD but service is failing to start.
We have been using standard FTP successful but need to introduce an FTPS option.
I have run YUM install VSFTPD and everything appeared to load ok.
(If I run rpm - qa | grep vsftpd I get vsftpd-2.0.5-16.el5_4.1 which I... (4 Replies)
When trying to connect from Mozilla's FireFTP using anonymous or a FTP user on the CentOS 5.7, using VSFTPD I get the following error:
550 Failed to change directory.(View Attachment)
This is what I have in my vsftpd.conf file:
# Example config file /etc/vsftpd/vsftpd.conf # # The default... (1 Reply)
Hi Guys,
I need to check why FTP service on Solaris 10 machine did not work in between.
What does Jun-29 means here? Does it mean that it has been RUNNING/UP since Jun 29th ?
-bash-3.2$ sudo /usr/bin/svcs |grep -i ftp
legacy_run Jun_29 lrc:/etc/rc3_d/S90proftpd
online ... (3 Replies)
Dear community,
I got the following error when I try to start the snmpd service:
# service snmpd start
Starting snmpd: Log say:
Could someone help please?
Thank you
Lucas
---------- Post updated at 08:07 AM ---------- Previous update was at 07:50 AM ----------
DAMN!!!!... (2 Replies)
Discussion started by: Lord Spectre
2 Replies
LEARN ABOUT DEBIAN
miredo-server.conf
MIREDO-SERVER.CONF(5) System Manager's Manual MIREDO-SERVER.CONF(5)NAME
miredo-server.conf - configuration for miredo-server
SYNOPSIS
miredo-server.conf
DESCRIPTON
miredo-server.conf is the configuration file for miredo-server. Each configuration directive consists of one directive name, possibly
followed by one or several spaces and a value for the directive. White spaces, empty lines and lines starting with '#' are ignored.
Directives are case-insensitive. A comprehensive list of the supported directives follows:
SERVER OPTIONS
ServerBindAddress server_ip
Specifies the primary IPv4 address of the Teredo server. miredo-server will bind to UDP/IPv4 port 3544 on this address and waits
for packets from Teredo clients. It will advertise the Teredo prefix which is defined with the Prefix directive.
A Teredo server needs two subsequent IPv4 addresses. It will wait for UDP IPv4 packets on port 3544 on both addresses. server_ip
specifies the lowest of both IPv4 addresses, which is known as the primary IPv4 server address. The secondary IPv4 address should be
server_ip + 1 and must also be assigned to the server.
ServerBindAddress2 server_ip2
It is possible to specify a secondary IPv4 server address manually. However, Miredo clients will need manual configuration (with
the ServerAddress2 directive in miredo.conf). Other Teredo clients are believed not to support such setup.
Prefix teredo_prefix
This directive specifies the Teredo prefix which the Teredo relay and/or server will advertise. teredo_prefix must be a valid IPv6
prefix.
The default value is 2001:0000::. A 32-bits prefix is required to use this option. Since you do not have such big an IPv6 prefix
YOU WILL NOT USE THIS OPTION. Moreover, certain third party Teredo client implementations require the default prefix.
InterfaceMTU mtu
This directive overrides the value of the MTU that is advertised to Teredo clients. The default value is 1280 bytes and should not
be changed if the default Teredo prefix is used.
YOU MUST NOT USE THIS OPTION with the default prefix. This would break interoperability with most Teredo relays.
SyslogFacility facility
Specify which syslog's facility is to be used by miredo-server for logging. Possible values are: daemon (the default), local0, ...
local7, kern and user (see syslog(2)).
SEE ALSO miredo-server(8)AUTHOR
Remi Denis-Courmont <remi at remlab dot net>
http://www.remlab.net/miredo/
miredo February 2008 MIREDO-SERVER.CONF(5)