Hello, I've got a FreeBSD 6 server running on my network that I used as a file server for my main computer. However I've really become frustrated with the slow up/down speeds I'm getting, about 100KB/s, which is about as bad as if I was using a "real" server. My setup is as follows:
Code:
ISP
|
Router
|
Hub
|
PowerLine node
[~10m]
PowerLine node
|
FreeBSD 6 Sever (256MB/450MHz Pentium)
[~3M]
Powerline node
|
Main Computer (Win7 using FileZilla)
Here are the results of tracert:
Code:
Tracing route to 192.168.1.15 over a maximum of 30 hops
1 319 ms 266 ms 242 ms 192.168.1.15
Trace complete.
It seems to be since we're just going over the LAN, I should really be getting at least 500KB/s+ right? Is this a PowerLine issue, cable issue, FreeBSD issue, PC hardware isssue... etc? I'd be very thankful if I can get some ideas where to start to identify the bottleneck here, thanks a lot.
On one of of solaris 7 boxes whenever i telnet or ftp it takes sometime before i get the prompt...any quick ideas where I should look...Thanks (3 Replies)
One of our most frequent questions is how to automate ftp transfers. There are several approaches. Since I'm writing this post, we will start with my favorite technique. :)
In Automated FTP task I present a simple example of my ksh co-process technique. And note that later in this thread I... (0 Replies)
just as the title says.
thanks.
#General Rule Sets
/sbin/ipfw add 0300 check-state
/sbin/ipfw add 0301 deny tcp from any to any in established
/sbin/ipfw add 0302 pass tcp from any to any out setup keep-state
/sbin/ipfw add 0303 pass udp from any to any out
#SSH FTP
/sbin/ipfw add 0400... (11 Replies)
When I ssh to my box, an Ultra 5. I get prompted for password immediately. I enter it and have to wait sometimes a full minute for it to prompt for a password.
The same thing happens when i try to ftp to the box, it will say connected, but it takes forever to prompt for password, and... (2 Replies)
SCO Unix 5.0.5 moving to Red Hat
Intel EtherExpress Pro/100+
Newbie that just started working for a company and having an issue with transfer speeds over the network. Need to move 1.5GB of data from an old server with a single SCSI HDD to a new server with RAID 5 SATA HDD's. Goal was to FTP... (4 Replies)
Hi again guys,
Earlier today, just all of a sudden, all SSH and FTP connections to my internal Linux box just slowed down to a crawl. After the connection/authentication though, everything was back to normal speed. Until you have to connect again. A box reboot didnt work either.
Now, from... (1 Reply)
How can one find the name and size of files ftp'ed during an old ftp transfer.
Is there any log where these details are stored or any UNIX command which can provide these details.
Thanks in advance. (4 Replies)
Hi All.
We are using AIX 5.3 ML9. There is 1 Gig NIC installed on two servers (Primary and Secondary) with Full Duplex Mode. We have scheduled a cronjob to copy the backup from primary to secondary thru FTP on WAN. The total data size is 15 GB and it took 9 Hours and 18 Mins with transfer rate... (6 Replies)
hi,
good morning.
Ma trying to ftp from one AIX machine to another on the same segment of the network. The ftp to eshtablish connection from machine A to machine B is quick, but the reverse is taking is much time (2 mins).
anyone can help me to solve this issue please (1 Reply)
Hello all. I have VSFTP up and ruining on ubuntu 10.04. It works great inside LAN, however when it comes to using it outside i have some problems. If i try to connect from filezila i get the listing and if i try to download it shows it will take forever to receive a file which is larger then 1mb,... (2 Replies)
Discussion started by: mantas1
2 Replies
LEARN ABOUT DEBIAN
theft-server
THEFT-SERVER(1p) User Contributed Perl Documentation THEFT-SERVER(1p)NAME
theft-server - CLC-INTERCAL networking
SYNOPSIS
theft-server --port=port [options]
DESCRIPTION
The theft-server mediates the communication between two CLC-INTERCAL programs with the internet extension. It keeps a list of process IDs
running on the current computer so it can provide lists of processes which can be engaged in INTERcal NETworking; it also responds to
broadcasts allowing other CLC-INTERCAL programs on the LAN to know there is something happening on this computer.
Under normal conditions, the theft-server is started automatically by a CLC-INTERCAL programs with the internet extension (unless one is
already running, of course!) because the extension cannot operate without a server on the local computer. However, it is possible to start
one manually, for example from a /etc/init.d or /etc/rc.d.
If the program is started automatically, it uses defaults for all its configuration; when started manually, it accepts the following
options:
-pport / --port=port
Uses the given port (number or service name) for communications, instead of using the default one from a configuration file.
-lseconds / --linger=seconds
Waits the specified time for a connection, then exit. The default is 600 (10 minutes). The timeout applies when the program starts and
also when all existing connections are closed. This allows the program to be started on demand by CLC-INTERCAL programs, and to auto-
matically exit when no longer required (unless more programs start up during the timeout).
This function is disabled by setting the timeout to 0 (i.e. -l0); for example, if starting the server from /etc/init.d or equivalent
one would disable the timeout.
-d / --debug
Tells everything it's doing (on Standard Error). Also, prevents the program from detaching from the current terminal and going into the
background.
BUGS
IPv6 is not yet implemented.
perl v5.8.8 2008-03-29 THEFT-SERVER(1p)
01-28-2010
