01-28-2010
well... I ended up setting a NTP server on another Linux box and it works fine...
So Linux host sync'ing with a Linux NTP server works....
Don't know if Linux host not sync'ing with AIX NTP server is a bug or unsupported configuration... anyways, my needs are fulfilled
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hi all,
I'm sure this question was asked before but I couldn't find what I was looking for in the 2 threads I found on here.
Here's my question/problem:
I have an isolated (no connection to outside world at all) Unix network. I want to have time sync between my other non-PC based system... (0 Replies)
Discussion started by: mariobernier
0 Replies
2. Solaris
hi
Please give me the configuration steps for NTP server.
How do i sync other servers with this NTP server
thanks to all (1 Reply)
Discussion started by: sijocg
1 Replies
3. UNIX for Dummies Questions & Answers
hello Guys,
I have an NTP problem on my SUN N240 server. External NTP server is being used for this box and when i run 'ntpq -p' i get connection refused message;
ntpq -p
ntpq: read: Connection refused
Here this is the ntp.conf file:
cat /etc/ntp.conf
# BEGIN NTP SERVERS
server... (6 Replies)
Discussion started by: dyavuzy1
6 Replies
4. Red Hat
hello,
I have installed RHEL 6.0 on my lappy in a separate partion with windows 7 on the hardware(not using VMWARE).Now kindly help me to active network configuration in that?????Is it require to have LINUX wireless drivers???? (1 Reply)
Discussion started by: dillipkmrpadhy
1 Replies
5. Solaris
hi all
ntp client side configuration file is done but in
# ntpq -p
remote refid st t when poll reach delay offset disp
==============================================================================
ntpserver .INIT. 16 u - 64 0 0.00 0.000... (5 Replies)
Discussion started by: nikhil kasar
5 Replies
6. Red Hat
Hi,
Can someone please help me configuring RIP (Routing Information Protocol v2 ). I have tried few manuals and posts from networking sites and i didnt get a clear picture.
This is what i have done:
1. Installed routed package and started routed service.
however, Dynamic routes are... (1 Reply)
Discussion started by: reddybs
1 Replies
7. Red Hat
Hi,
Could you please explain about "restrict" parameters in /etc/ntp.conf in ntp client and ntp Servers.
Example:
restrict 127.0.0.1
restrict -6 ::1
restrict 192.168.1.0 mask 255.255.255.0 nomodify notrap
Regards,
Mastan (1 Reply)
Discussion started by: mastansaheb
1 Replies
8. Red Hat
Hi All ,
I want a Good Specification For Building a Coustum PC must Have With Intel Motherboard and Intel Processor , And Must Have Virtualization , Cos im Gonna Install Redhat Enterprise Virtualization Based PC and Gonna install win Xp , Win 7 as a Guest Os in it .. Any one Have Good Spec for... (2 Replies)
Discussion started by: babinlonston
2 Replies
9. Red Hat
I wanted to know how to configure DNS configuration for RHEL 5.
I hope, my query is clear of how to setup DNS for RHEL 5.
Please revert with the reply to my query
Regards (6 Replies)
Discussion started by: RHCE
6 Replies
10. UNIX for Beginners Questions & Answers
I need to configure snmptrap on rhel 8 server and send trap to nimsoft for file system , memory and cpu load and network diconnection status.
please help me, if any one configured. (1 Reply)
Discussion started by: yash_message
1 Replies
LEARN ABOUT OPENSOLARIS
ntptrace
ntptrace(1M) System Administration Commands ntptrace(1M)
NAME
ntptrace - trace a chain of NTP hosts back to their master time source
SYNOPSIS
/usr/sbin/ntptrace [-vdn] [-r retries] [-t timeout]
[server]
DESCRIPTION
ntptrace determines where a given Network Time Protocol (NTP) server gets its time from, and follows the chain of NTP servers back to
their master time source. If given no arguments, it starts with localhost.
OPTIONS
The following options are supported:
-d Turns on some debugging output.
-n Turns off the printing of host names; instead, host IP addresses are given. This may be necessary if a nameserver is down.
-r retries Sets the number of retransmission attempts for each host.
-t timeout Sets the retransmission timeout (in seconds); default = 2.
-v Prints verbose information about the NTP servers.
EXAMPLES
Example 1 Sample Output From the ntptrace Command
The following example shows the output from the ntptrace command:
% ntptrace
localhost: stratum 4, offset 0.0019529, synch distance 0.144135
server2.bozo.com: stratum 2, offset 0.0124263, synch distance 0.115784
usndh.edu: stratum 1, offset 0.0019298, synch distance 0.011993, refid 'WWVB'
On each line, the fields are (left to right):
o The server's host name
o The server's stratum
o The time offset between that server and the local host (as measured by ntptrace; this is why it is not always zero for local-
host)
o The host's synchronization distance
o The reference clock ID (only for stratum-1 servers)
All times are given in seconds. Synchronization distance is a measure of the goodness of the clock's time.
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWntpu |
+-----------------------------+-----------------------------+
SEE ALSO
xntpd(1M), attributes(5)
BUGS
This program makes no attempt to improve accuracy by doing multiple samples.
SunOS 5.11 19 Mar 1998 ntptrace(1M)