01-19-2010
Make sure you have the proper timezone selected as your local time.
It can be set using /usr/sbin/timeconfig
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hi all,
I'm sure this question was asked before but I couldn't find what I was looking for in the 2 threads I found on here.
Here's my question/problem:
I have an isolated (no connection to outside world at all) Unix network. I want to have time sync between my other non-PC based system... (0 Replies)
Discussion started by: mariobernier
0 Replies
2. Solaris
hi
Please give me the configuration steps for NTP server.
How do i sync other servers with this NTP server
thanks to all (1 Reply)
Discussion started by: sijocg
1 Replies
3. UNIX for Dummies Questions & Answers
hello Guys,
I have an NTP problem on my SUN N240 server. External NTP server is being used for this box and when i run 'ntpq -p' i get connection refused message;
ntpq -p
ntpq: read: Connection refused
Here this is the ntp.conf file:
cat /etc/ntp.conf
# BEGIN NTP SERVERS
server... (6 Replies)
Discussion started by: dyavuzy1
6 Replies
4. Red Hat
hello,
I have installed RHEL 6.0 on my lappy in a separate partion with windows 7 on the hardware(not using VMWARE).Now kindly help me to active network configuration in that?????Is it require to have LINUX wireless drivers???? (1 Reply)
Discussion started by: dillipkmrpadhy
1 Replies
5. Solaris
hi all
ntp client side configuration file is done but in
# ntpq -p
remote refid st t when poll reach delay offset disp
==============================================================================
ntpserver .INIT. 16 u - 64 0 0.00 0.000... (5 Replies)
Discussion started by: nikhil kasar
5 Replies
6. Red Hat
Hi,
Can someone please help me configuring RIP (Routing Information Protocol v2 ). I have tried few manuals and posts from networking sites and i didnt get a clear picture.
This is what i have done:
1. Installed routed package and started routed service.
however, Dynamic routes are... (1 Reply)
Discussion started by: reddybs
1 Replies
7. Red Hat
Hi,
Could you please explain about "restrict" parameters in /etc/ntp.conf in ntp client and ntp Servers.
Example:
restrict 127.0.0.1
restrict -6 ::1
restrict 192.168.1.0 mask 255.255.255.0 nomodify notrap
Regards,
Mastan (1 Reply)
Discussion started by: mastansaheb
1 Replies
8. Red Hat
Hi All ,
I want a Good Specification For Building a Coustum PC must Have With Intel Motherboard and Intel Processor , And Must Have Virtualization , Cos im Gonna Install Redhat Enterprise Virtualization Based PC and Gonna install win Xp , Win 7 as a Guest Os in it .. Any one Have Good Spec for... (2 Replies)
Discussion started by: babinlonston
2 Replies
9. Red Hat
I wanted to know how to configure DNS configuration for RHEL 5.
I hope, my query is clear of how to setup DNS for RHEL 5.
Please revert with the reply to my query
Regards (6 Replies)
Discussion started by: RHCE
6 Replies
10. UNIX for Beginners Questions & Answers
I need to configure snmptrap on rhel 8 server and send trap to nimsoft for file system , memory and cpu load and network diconnection status.
please help me, if any one configured. (1 Reply)
Discussion started by: yash_message
1 Replies
LEARN ABOUT HPUX
systemd-rc-local-generator
SYSTEMD-RC-LOCAL-GENERATOR(8) systemd-rc-local-generator SYSTEMD-RC-LOCAL-GENERATOR(8)
NAME
systemd-rc-local-generator - Compatibility generator for starting /etc/rc.local and /usr/sbin/halt.local during boot and shutdown
SYNOPSIS
/lib/systemd/system-generators/systemd-rc-local-generator
DESCRIPTION
systemd-rc-local-generator is a generator that checks whether /etc/rc.local exists and is executable, and if it is pulls the
rc-local.service unit into the boot process. This unit is responsible for running this script during late boot. Note that the script will
be run with slightly different semantics than the original System V version, which was run "last" in the boot process, which is a concept
that does not translate to systemd. The script is run after network.target, but in parallel with most other regular system services.
systemd-rc-local-generator also checks whether /usr/sbin/halt.local exists and is executable, and if it is pulls the halt-local.service
unit into the shutdown process. This unit is responsible for running this script during later shutdown.
Support for both /etc/rc.local and /usr/sbin/halt.local is provided for compatibility with specific System V systems only. However, it is
strongly recommended to avoid making use of these scripts today, and instead provide proper unit files with appropriate dependencies for
any scripts to run during the boot or shutdown processes.
systemd-rc-local-generator implements systemd.generator(7).
SEE ALSO
systemd(1), systemctl(1)
systemd 237 SYSTEMD-RC-LOCAL-GENERATOR(8)