01-10-2010
Thanks for the response.
How do we use putty to connect to console when i connect the ILO LAN cable to net management port it is`nt pinging?
However i see that the light blinks.
9 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
looking for the answer to console port access via 25pin serial. Can i tip in from another unix box for access? (5 Replies)
Discussion started by: simplimarvelous
5 Replies
2. AIX
I have installed aix 5.2 on aix box through serial console connected to COM 1 . I even get a login prompt after the fresh installation . But as soon as i give a root & enter i again get a login prompt.i..e I am not able to logon after a fresh installation.
and even i configured IP configuration... (0 Replies)
Discussion started by: linuxnightowl84
0 Replies
3. Solaris
Hi all,
After the V890 server shutdown unexpectedly, it became unaccessible from RSC. There is one error message about it: rscadm: RSC firmware not responding
Do you have experienced this? Please help! (1 Reply)
Discussion started by: bamboonix
1 Replies
4. UNIX for Dummies Questions & Answers
Hi everybody
i am trying to telnet to sun server from win xp machine but getting message "x21 error connection closed by remote user". i had make changes in /etc/default/login & /etc/fuser file still i have not getting telnet access. my win xp machines ip is 10.205.121.177 & sun server ip is... (1 Reply)
Discussion started by: pshelke
1 Replies
5. Solaris
Hi,
Can anyone suggest me any USB Hard Disk Drive which I can connect to Sun Fire V890 and take backup at a quick speed. A test with SolidState USB Hard Drive for backup work was taking writing at 2GB per hour for a 75GB backup.
Regards,
Tushar Kathe (1 Reply)
Discussion started by: tushar_kathe
1 Replies
6. Solaris
Hi,
I want to know if there is a command available for obtaining the BIOS Serial Number on a Sun Fire V240 machine? Or is it a known issue that it cannot be obtained through any command?
Thanks,
Vineet (4 Replies)
Discussion started by: vineetd
4 Replies
7. Solaris
Hi Gurus
I would like to know whether break command always work well means take the system to ok> prompt. Its depend upon sever model also. As I am facing problem when ever my system ( Sunfire V890 ) having Solaris 10 OS & oracle RAC on it goes to hang state then I run the break command from... (6 Replies)
Discussion started by: girish.batra
6 Replies
8. Solaris
I am battling to get a V890 up and running. The system appears to have AUTOBOOT=false, so no OS comes up when it's powered on, and I do not have the credentials to get to the RSC management console. Output to ttya serial console ends at "Probing I/O buses", I assume because output is then being... (4 Replies)
Discussion started by: dstmark
4 Replies
9. Solaris
Hi Oracle Hardware Specialists,
I have shutdown a Sun Fire X2200 server running Solaris 10 x86 to single user mode to experiment some backup commands using Web based Sun embedded Lights Out Manager Redirection to open up a console session. However, it is not possible to copy & past text with... (7 Replies)
Discussion started by: gjackson123
7 Replies
dc(4) Kernel Interfaces Manual dc(4)
Name
dc - serial line/mouse/keyboard
Syntax
device dc0 at ibus? vector dcintr
Description
The serial line controller provides four ports, with modem control on two of the ports. The DECstation 3100 and DECstation 2100 only pro-
vide partial modem control. The DECstation 5000 provides full modem control. The ports are used as follows:
Port Usage
0 Graphics device keyboard at 4800 BPS
1 Mouse or tablet at 4800 BPS
2 Communications port 1 (w/modem control)/local terminal
3 Communications port 2 (w/modem control)/local terminal
Each communication port from the serial line controller behaves as described in and can be set to run at any of 16 speeds. For the encod-
ing, see
When a graphics device is not being used as the system console, communications port 2 becomes the system console. In this configuration,
the port can only be used at 9600 BPS and no modem control is supported.
The serial line driver operates in interrupt-per-character mode (all pending characters are flushed from the silo on each interrupt).
Restrictions
Speed must be set to 9600 BPS on the console port and 4800 BPS on ports used by graphics devices. The serial line driver enforces this
restriction; that is, changing speeds with the command may not always work on these ports.
Files
console terminal
local terminal
local terminal
See Also
console(4), devio(4), tty(4), ttys(5), MAKEDEV(8)
RISC dc(4)