12-17-2009
Quote:
Bus = 0
Device = 0
Function = 0
I did a check of a system running XP Pro.
The three values show in the network connections -->configure card window.
So a convoluted way to find out would be to temporarily replace the disk, and install XP then look at the network connection info.
10 More Discussions You Might Find Interesting
1. IP Networking
I have a UnixWare 2 server that has an ISA 3Com NIC that has just a BNC connector on it. I want to remove this and install an ISA 3Com NIC that has a BNC/RJ45 connector. What steps do I have to go through to successfully complete this? Thye are almost the exact same cards except for the... (1 Reply)
Discussion started by: cparks
1 Replies
2. IP Networking
The Octane is driving me nuts . It was sitting on the network doing its job nicely and i had to pull the n/w cable out from the wall to pull it from the inside of the table and connected it again . The logs show this -- link down .... < when i pulled it out >
link ok < when i connected >
But... (0 Replies)
Discussion started by: DPAI
0 Replies
3. UNIX for Advanced & Expert Users
I have been having trouble with my sis900 neytwork card in slacwkare linux. I tried to modprobe the sis900, it didnt give me any errors but it didnt load it. so I put in a realtek 8139 network card and tried it too. These are the errors i get with the two cards when trying to do insmod on either of... (3 Replies)
Discussion started by: The Fridgerator
3 Replies
4. UNIX for Dummies Questions & Answers
Hi!.
I have problems installing my network card under
ther redhat kernel.
First i tryed my integrated intel pro set 10/100
then my d-link 530tx Pci but none of them seems to
be found.
also i huse my network card to connect to the net
trough PPPOE where i need to type my username and... (3 Replies)
Discussion started by: Gibbler
3 Replies
5. SCO
Hi,
I was wondering if anyone could help me out with this problem. I have SCO 5.0.5 installed on a system that I am using 3c905b (3 Com) network card. This system is always powered on. After no certain time period this NIC doesn't work. I can't ping to this system from any other machine or vice... (2 Replies)
Discussion started by: AtALoss
2 Replies
6. UNIX for Dummies Questions & Answers
I have three network cards in my unix box. I need to figure out which card corresponds to an assigned IP address. If there some command in unix I can use to make an ethernet interface blink?
Any advice would be appreciated. (6 Replies)
Discussion started by: mojoman
6 Replies
7. Solaris
Hi Experts,
Can we use some command from unix to find the available network interface? I did tried
Its listing following, however how can I decide the which vender card is attached
e.g. if its hme , bge or some thing else
Thanks (7 Replies)
Discussion started by: kumarmani
7 Replies
8. SCO
SCO unix 5.0.5 - Suddently network lost & has to be reboot. I try to stop TCP & start TCP. but no connection. Any idea about that.
thanks (8 Replies)
Discussion started by: ajantha
8 Replies
9. Solaris
Hi All,
Can somebody explain that whats the meaning of different interfaces naming scheme, Like ' hme, qfe, e1000g0, ce, eri, bge' ?
This is such a basic question which i always overlooked :(
Thanks ! (6 Replies)
Discussion started by: Solarister
6 Replies
10. Red Hat
Dear All ,
While taking backups in one Linux Server , we find one alert came with regard to Network Interface Card.
Pl find the below alert.
Network Interface Card performance for NIC:eth1 has exceeded Major threshold.
Bytes sent and received per second (Average)= 105540.303101... (6 Replies)
Discussion started by: jegaraman
6 Replies
LEARN ABOUT DEBIAN
load_dat_font
load_dat_font(3alleg4) Allegro manual load_dat_font(3alleg4)
NAME
load_dat_font - Loads a FONT from an Allegro datafile.
SYNOPSIS
#include <allegro.h>
FONT *load_dat_font(const char *filename, RGB *pal, void *param)
DESCRIPTION
Loads a FONT from an Allegro datafile. You can set param parameter to point to an array that holds two strings that identify the font and
the palette in the datafile by name. The first string in this list is the name of the font. You can pass NULL here to just load the first
font found in the datafile. The second string can be used to specify the name of the palette associated with the font. This is only
returned if the pal parameter is not NULL. If you pass NULL for the name of the palette, the last palette found before the font was found
is returned. You can also pass NULL for param, which is treated as if you had passed NULL for both strings separately. In this case, the
function will simply load the first font it finds from the datafile and the palette that precedes it.
For example, suppose you have a datafile named `fonts.dat' with the following contents:
FONT FONT_1_DATA
FONT FONT_2_DATA
FONT FONT_3_DATA
PAL FONT_1_PALETTE
PAL FONT_2_PALETTE
Then the following code will load FONT_1_DATA as a FONT and return FONT_1_PALETTE as the palette:
FONT *f;
PALETTE pal;
char *names[] = { "FONT_1_DATA", "FONT_1_PALETTE" }
f = load_dat_font("fonts.dat", pal, names);
If instead you want to load the second font, FONT_2, from the datafile, you would use:
FONT *f;
PALETTE pal;
char *names[] = { "FONT_2_DATA", "FONT_2_PALETTE" }
f = load_dat_font("fonts.dat", pal, names);
If you want to load the third font, but not bother with a palette, use:
FONT *f;
char *names[] = { "FONT_3_DATA", NULL }
f = load_dat_font("fonts.dat", NULL, names);
RETURN VALUE
Returns a pointer to the font or NULL on error. Remember that you are responsible for destroying the font when you are finished with it to
avoid memory leaks.
SEE ALSO
register_font_file_type(3alleg4), load_font(3alleg4)
Allegro version 4.4.2 load_dat_font(3alleg4)