Sponsored Content
Operating Systems SCO Problems with network card in SCO Post 302381068 by edfair on Thursday 17th of December 2009 05:31:04 AM
Old 12-17-2009
If things were working before and don't work now it may be a dead card.
If only one network card the /dev/net1 is an error. cat /usr/adm/messages to see what reported last as the system booted.
How about using scoadmin, networks, network config manager, hardware to rip the network card out of the system then reboot and reinstall. Would require redoing tcpip afterwards. Haven't used that card so don't know what might be required to clean the drivers out.
 

10 More Discussions You Might Find Interesting

1. IP Networking

network card

I have a UnixWare 2 server that has an ISA 3Com NIC that has just a BNC connector on it. I want to remove this and install an ISA 3Com NIC that has a BNC/RJ45 connector. What steps do I have to go through to successfully complete this? Thye are almost the exact same cards except for the... (1 Reply)
Discussion started by: cparks
1 Replies

2. IP Networking

Network Card with SGI

The Octane is driving me nuts . It was sitting on the network doing its job nicely and i had to pull the n/w cable out from the wall to pull it from the inside of the table and connected it again . The logs show this -- link down .... < when i pulled it out > link ok < when i connected > But... (0 Replies)
Discussion started by: DPAI
0 Replies

3. UNIX for Advanced & Expert Users

Network Card Help

I have been having trouble with my sis900 neytwork card in slacwkare linux. I tried to modprobe the sis900, it didnt give me any errors but it didnt load it. so I put in a realtek 8139 network card and tried it too. These are the errors i get with the two cards when trying to do insmod on either of... (3 Replies)
Discussion started by: The Fridgerator
3 Replies

4. UNIX for Dummies Questions & Answers

Network card and internet

Hi!. I have problems installing my network card under ther redhat kernel. First i tryed my integrated intel pro set 10/100 then my d-link 530tx Pci but none of them seems to be found. also i huse my network card to connect to the net trough PPPOE where i need to type my username and... (3 Replies)
Discussion started by: Gibbler
3 Replies

5. SCO

3c905b network card problem with SCO 5.0.5

Hi, I was wondering if anyone could help me out with this problem. I have SCO 5.0.5 installed on a system that I am using 3c905b (3 Com) network card. This system is always powered on. After no certain time period this NIC doesn't work. I can't ping to this system from any other machine or vice... (2 Replies)
Discussion started by: AtALoss
2 Replies

6. UNIX for Dummies Questions & Answers

How can I tell which network card is which?

I have three network cards in my unix box. I need to figure out which card corresponds to an assigned IP address. If there some command in unix I can use to make an ethernet interface blink? Any advice would be appreciated. (6 Replies)
Discussion started by: mojoman
6 Replies

7. Solaris

How to identifying the network card ?

Hi Experts, Can we use some command from unix to find the available network interface? I did tried Its listing following, however how can I decide the which vender card is attached e.g. if its hme , bge or some thing else Thanks (7 Replies)
Discussion started by: kumarmani
7 Replies

8. SCO

network problems with sco

SCO unix 5.0.5 - Suddently network lost & has to be reboot. I try to stop TCP & start TCP. but no connection. Any idea about that. thanks (8 Replies)
Discussion started by: ajantha
8 Replies

9. Solaris

Network Card Name details

Hi All, Can somebody explain that whats the meaning of different interfaces naming scheme, Like ' hme, qfe, e1000g0, ce, eri, bge' ? This is such a basic question which i always overlooked :( Thanks ! (6 Replies)
Discussion started by: Solarister
6 Replies

10. Red Hat

Regarding Network Interface Card

Dear All , While taking backups in one Linux Server , we find one alert came with regard to Network Interface Card. Pl find the below alert. Network Interface Card performance for NIC:eth1 has exceeded Major threshold. Bytes sent and received per second (Average)= 105540.303101... (6 Replies)
Discussion started by: jegaraman
6 Replies
CARD(1) 								FSF								   CARD(1)

NAME
card - print reference card of program options SYNOPSIS
card [OPTION]... PROGRAM... DESCRIPTION
Print a reference card of the PROGRAMs thanks to their inline help. OPTIONS
-h, --help display this help and exit -v, --version display version information and exit -o, --output=FILE save the output in FILE -l, --language=LL print the help in the language LL (default: English) --command=CMD perform pretty-printing on the output of CMD (e.g. --command='netscape -help') Options for a2ps are given after `--', for instance $ card -lfr a2ps -- -Pdisplay -4 News, updates and documentation: http://www.inf.enst.fr/~demaille/a2ps/ AUTHOR
Written by Akim Demaille. REPORTING BUGS
Report bugs to <bug-a2ps@gnu.org>. COPYRIGHT
Copyright (C) 1997-99 Akim Demaille, Miguel Santana This is free software; see the source for copying conditions. There is NO warranty; not even for MERCHANTABILITY or FITNESS FOR A PARTICU- LAR PURPOSE. SEE ALSO
a2ps(1), card(1), fixps(1), pdiff(1), psset(1), texi2dvi4a2ps(1). The full documentation for card is maintained as a Texinfo manual. If the info and card programs are properly installed at your site, the command info card should give you access to the complete manual. card 1.3 (GNU a2ps 4.14) March 2014 CARD(1)
All times are GMT -4. The time now is 04:57 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy