Input
Output
Depending on how many header available, I hope able to rename all the header to this specific format like : MG_PN_0001SPV001,MG_PN_0002SPV001,MG_PN_0003SPV001,...,etc
say i have these many file in a directory named exam.
1)/exam/newfolder/link.txt.
2)/exam/newfolder1/
and i create a tar say exam.tar
well the problem is,
when i read the tar file i dont find any metadata about the directories,as you cannot create a tar containig empty directories.
on the... (2 Replies)
awk experts,
I have a big file of 4000 columns with header. Would like to print the columns with string value of "Commands" in header. File has "," separator. This file is on ESX host with Bash.
Thanks,
Arv (21 Replies)
Friends,
I need help with the following in UNIX.
Merge all csv files in one folder considering only 1 header row and ignoring header of all other files.
FYI - All files are in same format and contains same headers.
Thank you (4 Replies)
Hi All,
I have got a requirement.
I have a source file, EMPFULL.txt and I need to split the data for every 30 records
and place a Typical Header as below with system and page number too.
2012.01.03 Employee Dept Report 1... (6 Replies)
Hi,
I have an input like this
1 2 3 4
2 3 4 5
4 5 6 7
I would like to count the no. of columns and print a header with a prefix "Col".
I would also like to count the no. of rows and print as first column with each line number with a prefix "Row"
So, my output would be
... (2 Replies)
Hello There...
I have a sample input file ..
number:department:amount
125:Market:125.23
126:Hardware store:434.95
127:Video store:7.45
128:Book store:14.32
129:Gasolline:16.10
I will be doing some manipulations on all the records except the header, but the header should always be... (2 Replies)
I have this code below that only prints out certain columns from the first two rows (doesn't affect rows 3 and beyond). How can I do the same on a partial header pattern “G_TP” instead of having to know specific column numbers (e.g. 374-479)? I've tried many other commands within this pipe with no... (4 Replies)
I've been struggling with this one for quite a while and cannot seem to find a solution for this find/replace scenario. Perhaps I'm getting rusty.
I have a file that contains a number of metrics (exactly 3 fields per line) from a few appliances that are collected in parallel. To identify the... (3 Replies)
Discussion started by: verdepollo
3 Replies
LEARN ABOUT DEBIAN
slugimage
SLUGIMAGE(1) General Commands Manual SLUGIMAGE(1)NAME
slugimage - Manipulate NSLU2 firmware images
SYNOPSIS
slugimage [-p|-u] [options]
DESCRIPTION
slugimage can be used to create or unpack NSLU2 firmware images.
OPTIONS -d, --debug
Turn on debugging output
-q, --quiet
Turn off status messages
-u, --unpack
Unpack a firmware image
-p, --pack
Pack a firmware image
-l, --little
Convert Kernel and Ramdisk to little-endian
-i, --input
Input firmware image filename
-o, --output
Output firmware image filename
-b, --redboot
Input/Output RedBoot filename
-k, --kernel
Input/Ouptut Kernel filename
-s, --sysconf
Input/Output SysConf filename
-r, --ramdisk
Input/Output Ramdisk filename(s)
-f, --fisdir
Input/Output FIS directory filename
-y, --payload
Input/Output Payload filename
-t, --trailer
Input/Output Trailer filename
-e, --ethaddr
Set the Ethernet address
AUTHOR
This man page was written by Joey Hess, <joey@kitenet.net>.
SLUGIMAGE(1)