Serial port on the T5140 Post: 302380184

10 More Discussions You Might Find Interesting

1. Programming

Serial port programming

I am developing an application in c with Linux OS, where a radio modem working at baud rate 9600 will be attached to PC on serial port. More than four such units will be communicating at one time, so there may be jamming or data corruption. Each module will be transmitting Data packets less than...

2. Solaris

Serial port issue

Hi, I am working with Sun Solaris 9 Sparc,Sun-Blade-100.In my application,I need to monitor the UPS using Serial port. When I am using JRE 1.4 in my application,I am able to monitor it but when I am upgrading the JRE version from 1.4 to JRE1.6. I am not able to monitor the UPS.It is showing the...

3. Programming

Programming serial port

Hello! Can someone advice me which method I will use if I want to communicate with device via RS232 serial port with this requirements: 1. Serial port is opened in non-canonical mode. 2. All the time I need to check is there something to read. 3. If I have to write something I need to write it...

4. Programming

How to tell if a string to serial port has been sent

I have a need to determine when a string has been completely sent via a serial port from a standard 'C' application. The code is as follows: SerialPort_Send = open (pPortString, O_WRONLY | O_NOCTTY | O_NONBLOCK); write (SerialPort_Send, pCommandString, strlen (pCommandString)); ...

5. UNIX for Dummies Questions & Answers

Missing serial port

A neighbour's Ubuntu 10.04 machine has five serial ports, one on the motherboard and four on a PCI card. However, only four cards are showing: # dmesg | grep tty console enabled serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A 00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A ...

6. Shell Programming and Scripting

Need help with serial port

Hi, I have a external board connected to my serial port. I need to execute "shutdown -r now" command when system boot up. When system boots up it requires a username ans password. Then I need to run my command. I can use rc script but that is rebooting system before it asks for username and...

7. Solaris

How to enable Serial port on ILOM, when Network Port is enabled in parallel

Hi Everyone, In my environment, I have few T5220. On the iLOM Management Card, I have both Network and Serial port are cabled, I don't have any issues while I try to connect using Network Management port, but when I try to connect the serial port for the same server which is actually connected...

8. Programming

Read from serial port

Hi I try to communicate with a GSM modem, from C, for sending SMS. I use standart AT-commands. Working well with terminal. There is no problem writing ti the port. But when I try to read I only get a echo, I write "ATI" and get "ATI" back, I should get somthing like "SIEMENS 35...

9. Web Development

Writing to a Serial Port

I am trying to write to a serial port and capture the reponse in a file - adduser ethan dialout The user `ethan' is already a member of `dialout' root@meow:/home/ethan# ls -l /dev/ttyS0 crw-rw-r-- 1 ethan dialout 4, 64 Oct 7 20:55 /dev/ttyS0 $fh1 = fopen("/dev/ttyS0", "w+");...

10. Solaris

Cabling and adapters to communicate to service processor serial port from Windows PC with USB port.

Hello, I have an unloaded T5140 machine and want to access the ILOM for the first time and subsequently the network port after that., and then load Solaris 10 the final January 2011 build. The first part is what confuses me -the cabling. I am coming from a Windows machine (w/appropriate...

LEARN ABOUT NETBSD

spif

SPIF(4) 						   BSD Kernel Interfaces Manual 						   SPIF(4)

NAME

     spif -- SBus (spiffy) Serial/Parallel Interface

SYNOPSIS

     spif* at sbus? slot ? offset ?		    (sun4c/sun4m/sun4u)
     stty* at spif?				    (sun4c/sun4m/sun4u)
     sbpp* at spif?				    (sun4c/sun4m/sun4u)

DESCRIPTION

     The spif driver provides support for the Sun Serial/Parallel Interface card (Sun part number 501-1931), which is based on the Cirrus Logic
     CD180 octal serial controller and the Cirrus Logic PPC2 parallel port controller.

     The device minor numbers for this driver are encoded as follows:

	 +---+---+---+---+---+---+---+---+
	 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
	 +---+---+---+---+---+---+---+---+
	   |   |   |   |   |   |   |   |
	   |   |   |   |   |   +---+---+---> port number
	   |   |   |   |   |
	   |   |   |   |   +---------------> unused
	   |   |   |   |
	   |   |   |   +-------------------> dial-out (on tty ports)
	   |   |   |
	   |   |   +-----------------------> unused
	   |   |
	   +---+---------------------------> card number

     Up to four cards are supported in the system.

     Each of the serial ports has an 8 byte FIFO for receive and transmit as well as automatic hardware (RTS/CTS) flow control.

FILES

     /dev/ttyS[0123][0-7]  Serial ports
     /dev/bppS[0-3]	   Parallel ports

DIAGNOSTICS

     spif%d: ccr timeout  A timeout occurred while writing to one of the CD180 registers.

     stty%d-%d: ring overflow  Incoming characters were discarded because the application in control of the device did not read the input fast
     enough.

SEE ALSO

     intro(4), sbus(4), tty(4)

HISTORY

     The spif adapter was first supported in OpenBSD 2.5.  The driver was ported to NetBSD 3.0.

AUTHORS

     The driver was written by Jason Wright <jason@thought.net>, and is heavily based on the magma(4) driver written by Iain Hibbert.

TODO

     The parallel port is not supported yet.

     Dial-out (cua) devices are not yet supported.

BSD
								 February 4, 1999							       BSD

10 More Discussions You Might Find Interesting

1. Programming

Serial port programming

Discussion started by: raj8109

2. Solaris

Serial port issue

Discussion started by: smartgupta

3. Programming

Programming serial port

Discussion started by: jvrlic

4. Programming

How to tell if a string to serial port has been sent

Discussion started by: ExDes