I'm writing a script to find the oldest file in a directory. I know this can be done by using ls -rt | tail -1 but these are rather large directories and that can be somewhat slow since the script will be running constantly.
Are there any other ways to do this that would be faster? I looked to... (2 Replies)
Hi all,
I need your assistance in removing the oldest file in a directory.
I posted the same thread 3 days back and I got the following answer
ls -1 -t | tail -1 | xargs rm
which is not covering the case when there are directories older than the oldest file.
So, could you please... (2 Replies)
I am using a bash script to perform some automated maintenance on files in a directory. When I run the script using $sh -x script.sh <directory> the script works fine. It sets the variable to the oldest file, and continues on. However when I run the script like this $./script.sh <directory>, it... (5 Replies)
Hi all,
I am a newbie to scripting and I need your help regarding finding the oldest file in a particular directory. My intention is to remove that oldest file.
Are there any options available with the "find" command to do this..
Thanks in advance for your help
Pavan (4 Replies)
I am trying to determine the oldest and most recent files in a huge directory. I am using an ls -tr statement outside my find statement. The directory is too big and I am getting an "arg list too long" error. Is there something I can put in my find statement that doesn't create a list to... (2 Replies)
The `bash` below uses the oldest folder in the specified directory and logs it. The goes though an analysis process and creates a log. My problem is that if there are 3 folders in the directory folder1,folder2,folder3, the bash is using folder2 for the analysis eventhough folder1 is the oldest... (0 Replies)
In the bash below the oldest folder in a directory is selected. If there are 3folders in the directory /home/cmccabe/Desktop/NGS/test and nothing is done to them (ie. no files deleted, renamed) then the bash correctly identifies f1 as the oldest. However, if something is done to the folder then... (4 Replies)
Discussion started by: cmccabe
4 Replies
LEARN ABOUT SUSE
irsend
IRSEND(1) FSF IRSEND(1)NAME
irsend - basic LIRC program to send infra-red commands
SYNOPSIS
irsend [options] DIRECTIVE REMOTE CODE [CODE...]
DESCRIPTION
Asks the lircd daemon to send one or more CIR (Consumer Infra-Red) commands. This is intended for remote control of electronic devices such
as TV boxes, HiFi sets, etc.
DIRECTIVE can be:
SEND_ONCE - send CODE [CODE ...] once
SEND_START - start repeating CODE
SEND_STOP - stop repeating CODE
LIST - list configured remote items
SET_TRANSMITTERS - set transmitters NUM [NUM ...]
SIMULATE - simulate IR event
REMOTE is the name of a remote, as described in the lircd configuration file.
CODE is the name of a remote control key of REMOTE, as it appears in the lircd configuration file.
NUM is the transmitter number of the hardware device.
For the LIST DIRECTIVE, REMOTE and/or CODE can be empty:
LIST "" "" - list all configured remote names
LIST REMOTE "" - list all codes of REMOTE
LIST REMOTE CODE - list only CODE of REMOTE
The SIMULATE command only works if it has been explicitly enabled in lircd.
-h --help
display usage summary
-v --version
display version
-d --device
use given lircd socket [/var/run/lirc/lircd]
-a --address=host[:port]
connect to lircd at this address
-# --count=n
send command n times
EXAMPLES
irsend LIST DenonTuner ""
irsend SEND_ONCE DenonTuner PROG-SCAN
irsend SEND_ONCE OnkyoAmpli VOL-UP VOL-UP VOL-UP VOL-UP
irsend SEND_START OnkyoAmpli VOL-DOWN ; sleep 3
irsend SEND_STOP OnkyoAmpli VOL-DOWN
irsend SET_TRANSMITTERS 1
irsend SET_TRANSMITTERS 1 3 4
irsend SIMULATE "0000000000000476 00 OK TECHNISAT_ST3004S"
FILES
/etc/lirc/lircd.conf
Default lircd configuration file. It should contain all the remotes, their infra-red codes and the corresponding timing and wave-
form details.
DIAGNOSTICS
If lircd is not running (or /var/run/lirc/lircd lacks write permissions) irsend aborts with the following diagnostics:
"irsend: could not connect to socket"
"irsend: Connection refused" (or "Permission denied").
SEE ALSO
The documentation for lirc is maintained as html pages. They are located under html/ in the documentation directory.
lircd(8), mode2(1), smode2(1), xmode2(1), irrecord(1), irw(1), http://www.lirc.org.
irsend 0.8.7pre1 May 2010 IRSEND(1)