|
|
Sponsored Content
Operating Systems
AIX
AIX(VIO/LPAR) with Free NAS ISCSI solution
Post 302377798 by kabir on Saturday 5th of December 2009 07:54:56 AM
12-05-2009
|
|
10 More Discussions You Might Find Interesting
1. AIX
I have a standard template I deploy for each of my AIX servers. It's in a mksysb format which I pulled via the nim server after I originally set it up.
I'm trying to restore this mksysb over the wire to a remote system. The remote system is an lpar running under vio (no HMC attached). The disk... (1 Reply)
Discussion started by: scottsl
1 Replies
2. UNIX for Dummies Questions & Answers
Can you have a Dynamic LPAR without VIO and if yes is there a benefit to having both? I am attempting to implement VIO and Resource pooling at my company and want to understand the limitations.
Also, I have been told the managing and allocation of the Logical Volumes is a time consuming task as... (0 Replies)
Discussion started by: bombers73
0 Replies
3. AIX
We have a frame the uses 2 vios that assign disk storage to LPAR's. We have a LPAr with multiple disk and I want to know how do I tell which vio is serving the disk. For example the LPAr has hdisk 0, 1, 2, 3 all the same size. I want to know which vio is serving hdisk0, 1. (4 Replies)
Discussion started by: daveisme
4 Replies
4. AIX
VIO Server is managing both AIX Clients and Linux Clients. For AIX Clients, we could do a disk mapping from slot numbers to VIO and also uname -L to determine the lparid and serial number frame its running on.
From a Linux Client,
How do I know which IBM frame its running on? Any command to... (4 Replies)
Discussion started by: rpangulu
4 Replies
5. AIX
I am wondering if there is a command I can run from **with-in** LPAR server (server01) to find out the hostname or IP address or other parameters for VIO server in charge of server01? (1 Reply)
Discussion started by: ms1232
1 Replies
6. AIX
Just a question which may seem dumb to some out there, but then again I am not a super technie so that's my excuse.
Is it possible to say provision a test AIX LPAR (has a 10gb boot lun and 20gb data) under a VIO which has connectivity to SAN Array A so it can see the disks provisioned to it,... (2 Replies)
Discussion started by: Johnny1314
2 Replies
7. AIX
Previous forum threads have noted that AIX cannot use iSCSI disks because it fails when trying to add them to a volume group using mkvg. The failure is caused by AIX's use of the SCSI "WRITE AND VERIFY"(0x2e) command which some iSCSI targets do not support.
We experienced the same problem using... (1 Reply)
Discussion started by: garethr
1 Replies
8. AIX
Hi All,
I've been trying to create a new LPAR for some days now but I can't get the VIO server to recognize the new LPAR. This is what I did:
On HMC create new LPAR
On HMC create new virtual scsi adapter for LPAR in VIO profile
On HMC add new virtual scsi adapter for LPAR with DLPAR... (6 Replies)
Discussion started by: petervg
6 Replies
9. Linux
I am using Windows Server 2008R2 as a domain controller to 2 other servers and would like to use my Dell Powervault 770N as my NAS for data storage. I have FC that I would like to implement between the servers and the NAS (as an iSCSI target). I am brand new to this world; is this possible? I am... (2 Replies)
Discussion started by: NoviceAdmin
2 Replies
10. AIX
:wall::wall::wall:
1. I have created an LPAR in the HMC.
2. I have allocated the storage from an Hitachi AMS2500 and assigned it to the host group.
3. I have zoned the LPAR and Storage on a Brocade 5100. (The zone sees the AMS)
Next I activated the LPAR in the HMC, SMS mode for the mksysb... (3 Replies)
Discussion started by: Dallasguy7
3 Replies
LEARN ABOUT CENTOS
checkrad
CHECKRAD(5) File Formats Manual CHECKRAD(5) NAME
checkrad -- See if a user is (still) logged in on a certain port. SYNOPSIS
checkrad [-d] nas-type nas-ip nas-port login session-id DESCRIPTION
Checkrad is used by the radius server to check if its idea of a user logged in on a certain port/NAS is correct if a double login is detected. Returns: 0 = no duplicate, 1 = duplicate, >1 = error. OPTIONS
-d Enable printing of debugging informations. nas-type Type of port/NAS. Can be one of: o ascend o bay o cisco o cisco_l2tp o computone o cvx o digitro o dot1x o livingston o max40xx o mikrotik o mikrotik_snmp o multitech o netserver o other o pathras o patton o portslave o pr3000 o pr4000 o redback o tc o usrhiper o versanet The "other" type cause checkrad to skip any check and always returns 1. nas-ip IP address of the NAS to check. nas-port The NAS port to check (may be ignored by some nas-type). login The login name to check. session-id Session to check. (actually ignored by all nas-type) SEE ALSO
radiusd(8) AUTHOR
Written by Miquel van Smoorenburg, miquels@cistron.nl. This manual page was written by Marco Nenciarini <mnencia@debian.org> for the Debian project (but may be used by others). 13 January 2006 CHECKRAD(5)