12-02-2009
check out the syslog.conf file. anyway its a prod box, so how do you think you want to stop the inetsvc daemon?
syslogd — the system daemon used to receive and route system log events from syslog() calls and logger commands
/etc/syslog.conf — the configuration file used to control the logging and routing of system log events
# /etc/init.d/inetsvc stop
after vts complete,
# /etc/init.d/inetsvc start
can???
Last edited by incredible; 12-02-2009 at 12:16 PM..
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Ok, So I've been lazy over the past 3 years with the SCO server I maintain, as it just primarily hosts my private networked proprietary software, until now.
We have dedicated net access, in which the SCO server is not setup for and not going to be setup to connect to the internet by any direct... (8 Replies)
Discussion started by: ftn96
8 Replies
2. Shell Programming and Scripting
Hi
I have a question, what is the purpose of this command and what will it do
"refresh -s inetd"
Thanks in Advance
Swaraj (3 Replies)
Discussion started by: kswaraj
3 Replies
3. HP-UX
--------------------------------------------------------------------------------
Hi All ,
I have a client an server among which i want to make the server an inetd process.
I have enries in etc/services and etc/inetd.conf
The enries looks like below
etc/services
servername 5551/tcp... (4 Replies)
Discussion started by: binums
4 Replies
4. HP-UX
To anyone who can help.
I am trying to get VNC running using the inetd capability and I am having problems. I have VNC running fine when I manually log into the server through FTP or SSH and start it and then start the viewer on my PC.
I have tried a few things I have found on different... (0 Replies)
Discussion started by: punkdeviant
0 Replies
5. Red Hat
I need to put the following line in inetd.conf:
stats stream tcp nowait nobody /usr/local/bin/mrtgsysinfo mrtgsysinfo
but my version of linux don't seem to allow that, ie there is no inetd.conf. How do i set that up in linux (red hat enterprise 3). (15 Replies)
Discussion started by: frankkahle
15 Replies
6. IP Networking
Hi , I need help, today I restarted the server, when the machine was up, it had been to writte in the file osmlog that :
"inetd: talk/udp: bind: Address already in use"
This message appears in ten minutes every time. Why ?
Thanks. (6 Replies)
Discussion started by: By_Jam
6 Replies
7. UNIX for Dummies Questions & Answers
I'm trying to edit the inetd.conf but for some reason when I vi into it, it says "Read Only" even though I am root and the perms are 777?!? (2 Replies)
Discussion started by: shorty
2 Replies
8. UNIX for Dummies Questions & Answers
hi,
is it ok for more than one inetd daemon running at a time?
if not okay, possible to kill the rest and make only one daemon running?
i understand that inetd is a process that enables tcp connections from external sources...kindly advise more on inetd...thanks alot..Happy New Year!:) (2 Replies)
Discussion started by: cromohawk
2 Replies
9. Solaris
Hi All,
When i am trying to restart the inetd daemon it throughing error.
Please find the message and tell me what i need to do ?
Apr 7 22:57:37 HYDOHS01 inetd: ISTATE not in environment
Apr 7 22:57:41 HYDOHS01 inetd: stop: No such file or directory
Apr 7 22:58:01 HYDOHS01 inetd: ... (5 Replies)
Discussion started by: lbreddy
5 Replies
10. Solaris
inet not running on the zone , below is the error we see on svc log
Importing 100235_1-rpc_ticotsord.xml ...Done
inetconv: Error reading from repository
inetconv: Notice: Service manifest for 100235/1 already generated as /var/svc/manifest/network/rpc/100235_1-rpc_ticotsord.xml, skipped... (0 Replies)
Discussion started by: skamal4u
0 Replies
LEARN ABOUT OSF1
syslog.conf
syslog.conf(4) Kernel Interfaces Manual syslog.conf(4)
NAME
syslog.conf - syslogd configuration file
SYNOPSIS
facility.severity destination Where: Is part of the system generating the message, specified in /usr/include/sys/syslog_pri.h.
See also the syslogd(8) reference page. The severity level, which can be emerg, alert, crit, err, warning, notice, info, or debug. See
/usr/include/sys/syslog_pri.h.
The syslogd daemon logs all messages of the specified severity level plus all messages of greater severity. For example, if you
specify level err, all messages of levels err, crit, alert, and emerg or panic are logged. A local file pathname to a log file, a
host name for remote logging or a list of users. In the latter case the users will receive messages when they are logged in. An
asterisk (*) causes a message to be sent to all users who are currently logged in.
DESCRIPTION
The /etc/syslog.conf file is a system file that enables you to configure or filter events that are to be logged by syslogd. You can specify
more than one facility and its severity level by separating them with semicolons.
You can specify more than one facility logs to the same file by separating the facilities with commas, as shown in the EXAMPLES section.
The syslogd daemon ignores blank lines and lines that begin with an octothorpe (#). You can specify # as the first character in a line to
include comments in the file or to disable an entry. The facility and severity level are separated from the destination by one or more tab
characters.
If you want the syslogd daemon to use a configuration file other than the default, you must specify the file name with the following com-
mand: # syslogd -f config_file
Daily Log Files
You can specify in the /etc/syslog.conf file that the syslogd daemon create daily log files. To create daily log files, use the following
syntax to specify the path name of the message destination: /var/adm/syslog.dated/ { file} The file variable specifies the name of the log
file, for example, mail.log or kern.log. If you specify a /var/adm/syslog.dated/file path name destination, each day the syslogd daemon
creates a sub-directory under the /var/adm/syslog.dated directory and a log file in the sub-directory, using the following syntax:
/var/adm/syslog.dated/ date / file Where: The date variable specifies the day, month, and time that the log file was created. The file
variable specifies the name of the log file you previously specified in the /etc/syslog.conf file. The syslogd daemon automatically cre-
ates a new date directory every 24 hours and also when you boot the system. The current directory is a link to the latest date directory.
To get the latest logs, you only need to reference the /var/adm/syslog.dated/current directory.
EXAMPLES
The following is a sample /etc/syslog.conf file: # # syslogd config file # # facilities: kern user mail daemon auth syslog lpr binary #
priorities: emerg alert crit err warning notice info debug # kern.debug /var/adm/syslog.dated/kern.log user.debug /var/adm/sys-
log.dated/user.log daemon.debug /var/adm/syslog.dated/daemon.log auth.crit;syslog.debug /var/adm/syslog.dated/syslog.log mail,lpr.debug
/var/adm/syslog.dated/misc.log msgbuf.err /var/adm/crash.dated/msgbuf.savecore kern.debug /var/adm/messages kern.debug /dev/console *.emerg
*
FILES
/etc/syslog.conf
/etc/syslog.auth - Authorization file for remote logging.
/usr/include/sys/syslog_pri.h - Common components of a syslog event log record.
RELATED INFORMATION
Commands: /usr/sbin/syslogd(8), /usr/sbin/binlogd(8)
System Administration delim off
syslog.conf(4)