11-30-2009
Sorted
I sorted it by managaing to find a test server we could put APA on and testing various options.
Thanks
10 More Discussions You Might Find Interesting
1. Solaris
Hi there
I have a requirement to provide failover to our customer boxes in case of interface / switch failure, I have been looking at Solaris Link Aggregation with LACP and I wanted to ask a question
Ive seen multiple websites that say the following
Does this also mean that if the... (2 Replies)
Discussion started by: hcclnoodles
2 Replies
2. UNIX for Advanced & Expert Users
Hi there
I have a requirement to provide failover to our customer boxes in case of interface / switch failure, I have been looking at Solaris Link Aggregation with LACP and I wanted to ask a question
Ive seen multiple websites that say the following
Does this also mean that if the... (1 Reply)
Discussion started by: hcclnoodles
1 Replies
3. IP Networking
I have some linux machines that I am trying to increase the throughput to on a single connection. They connect to a switch with two 1GbE lines and the switch does not have Link Aggregation support for these machines. I have tried bonding with balance-rr, balance-alb, but the machines can only... (4 Replies)
Discussion started by: Eruditass
4 Replies
4. AIX
Hi,
I need to setup a hacmp cluster (my first one, we usually use VCS on AIX), but I require more network bandwith than a normal gigabit etherchannel setup can provide, so I am thinking about using linkaggregation - 2 active adapters to one switch and a single backup adapter to another switch... (4 Replies)
Discussion started by: zxmaus
4 Replies
5. Solaris
Me again :)
I'm trying to find a page describing the L2, L3 und L4 modes of dladm.
It's nice to read "hashed by ip header", but how should I use that?
On the file-server it's ok to have the six interfaces serving six clients each on it's own. But an rsync connection via switch between two... (8 Replies)
Discussion started by: PatrickBaer
8 Replies
6. HP-UX
Hi,
I want to Break the Link Aggregation. My aggregation are lan0+lan1 = lan900.
Now I want to break this and put the IP in lan0. But i have cluster environment and this is the main database server.
So It need to change in cluster script.
But I dont know where I have to change it.
Please... (1 Reply)
Discussion started by: mkiron
1 Replies
7. Solaris
Hi,
I'm not from the Solaris world and some of these things are new to me. Can someone tell me if it is possible to configure link aggregation without using LACP?
I am told etherchannel was setup without LACP. (3 Replies)
Discussion started by: techy1
3 Replies
8. Solaris
I have setup link aggregation with 3 interfaces on my solaris 10 system.
All looks good but my problem is that the traffic is only going out bge0 and not the other 2 links.
bash-4.3# dladm show-aggr -s
key:33 ipackets rbytes opackets obytes %ipkts %opkts
... (3 Replies)
Discussion started by: primeaup
3 Replies
9. IP Networking
Hi
ihave three link of internet and iwant to put one linux front of a firewall that this three linux speard firewall such az load balance and fialover but dont close any port and protocol and only firewall have been internet what way can i use for it ?
are there any script and services do that... (0 Replies)
Discussion started by: mnnn
0 Replies
10. Solaris
Hi,
I have Solaris-10 server and link aggregation is configured on this in below way
# dladm show-aggr
key: 1 (0x0001) policy: L4 address: 3c:d9:2b:ee:a8:a (auto)
device address speed duplex link state
bnx1 3c:d9:2b:ee:a8:a... (8 Replies)
Discussion started by: solaris_1977
8 Replies
LEARN ABOUT NETBSD
eshconfig
ESHCONFIG(8) BSD System Manager's Manual ESHCONFIG(8)
NAME
eshconfig -- configure Essential Communications' HIPPI network interface
SYNOPSIS
eshconfig [-estx] [-b bytes] [-c bytes] [-d filename] [-i usecs] [-m bytes] [-r bytes] [-u filename] [-w bytes] [interface]
DESCRIPTION
eshconfig is used to configure device-specific parameters and download new firmware to the Essential Communications RoadRunner-based HIPPI
network interface. The interface is very sensitive to the DMA performance characteristics of the host, and so requires careful tuning to
achieve reasonable performance. In addition, firmware is likely to change frequently, which necessitates a reasonably easy way to update
that firmware.
Available operands for eshconfig:
-b bytes
Adjust the burst size for read (by NIC of host memory) DMA.
-c bytes
Adjust the burst size for write (by NIC of host memory) DMA.
-d filename
Filename for file to download into NIC firmware. This must be a file in the standard Essential format, with :04 preceding every
line, and a tag line at the end indicating the characteristics of the firmware file.
-e Write data to EEPROM. Normally, setting tuning parameters will only persist until the system is rebooted. Setting this parameter
ensures that the changes will be written to EEPROM.
-i usecs
Interrupt delay in microseconds.
-m bytes
Minimum number of bytes to DMA in one direction (read or write) before allowing a DMA in the other direction. Tuning this prevents
one direction from dominating the flow of bytes, and artificially throttling the NIC.
-r bytes
Bytes before DMA starts for read (from host to NIC). This controls how soon the DMA is triggered; until this many bytes are
requested, the DMA will not begin.
-s Show statistics for the HIPPI NIC. Repeat the option to suppress non-zero statistics.
-t Show current tuning parameters on the host.
-u filename
Name of file to which the NIC firmware should be uploaded. Not currently supported.
-w bytes
Number of bytes required before write (from NIC to host) DMA is started. Until this many bytes are ready to be written, the DMA will
not start.
-x Reset the NIC. This is necessary for the HIPPI-FP support, as ifconfig(8) will no longer physically reset the NIC when the inter-
faces goes up and down.
Only the super-user may modify the configuration of a network interface.
DIAGNOSTICS
Messages indicating the specified interface does not exist or the user is not privileged and tried to alter an interface's configuration.
SEE ALSO
esh(4), ifconfig(8)
HISTORY
The eshconfig command first appeared in NetBSD 1.4.
BSD
June 17, 2005 BSD