11-24-2009
The /usr/adm/messages will show the same information as scrolls on the screen during the boot process. It probably will not show anything for the tape as it only reports found and configured hardware. If the tape is configured as scsi-id 2, and there is a device set to id 2 then the device will show in the file. If the tape is configured as 2, and the device is set to 3, then nothing will show in the messages file.
The POST (Power On Self Test) information displays on the screen prior to the Boot: prompt appearing, unless it has been suppressed in the CMOS setup. You should see the amount of memory in the system, and the scsi host adapter information followed by a line of description for the device type, brand, model and scsi id for each device found.
You may also see a prompt to run the scsi setup (<ctrl>-A for Adaptec, <ctrl>-M for Mylex) etc.
Yes the re-link is done during the mkdev tape process. The current kernel is renamed to unix.old, and the environment should be rebuilt.
Do not re-link the kernel twice without either re-booting to confirm that that the new kernel works, or otherwise saving /stand/unix.old. With 5.0.6 the kernel should fit on a 1.44 floppy.
Last edited by jgt; 11-24-2009 at 09:04 PM..
8 More Discussions You Might Find Interesting
1. Linux Benchmarks
Notes:
System Configuration: Dell Computer Corporation PowerEdge 4600 (4 X Intel(R) XEON(TM) CPU 2.00GHz
1988.782 MHz) hyperthreaded
System clock frequency: 99.0827 MHz
Memory size (approximate): 2559 Megabytes
========================= CPUs ========================
CPU # CPU... (0 Replies)
Discussion started by: tnorth
0 Replies
2. Linux Benchmarks
CPU/Speed: Dual PIII 533
Ram: 256Mb PC133
Motherboard: Unknown, Intel Chipset
Cache: 256k on board
Controller: PARC Raid 2/Si, AIC-7880U
Disk: 30Gb RAID 5
Load: 1 user. Clean boot, init 5 but X-Windows not loaded.
Kernel: See Benchmarks.
pgms: gcc 3.2.3
... (2 Replies)
Discussion started by: Garp
2 Replies
3. Solaris
hi, i am trying to install solaris 10 (on 4 cd's downloaded from the sun website) on my dell poweredge 2800 server. 2 xeon processors, 2GB of RAM and 2 NICS, 73 GB SCSI (maxtor ultra320, 3.5 series), i can give more details on request...
the installation crashes when trying to detect the NICS... (0 Replies)
Discussion started by: xinugeek
0 Replies
4. Red Hat
I have successfully installed RedHat 8.0 onto a Dell PowerEdge SC1425 today. This server has two SATA hard drives, and an IDE DVD-ROM drive.
Using the following kernel parameters, i successfully installed across both hard drives from CD:
ide0=0x1f0,0x3f6,14 vga=791 resolution=1024x768 expert... (5 Replies)
Discussion started by: fishsponge
5 Replies
5. Filesystems, Disks and Memory
Does anybody no how to get around the fact that the Red Hat installation does not see the SCSI hard drives. It lets you manually pick the proper device, but still fails saying no drive detected (or something to that effect). I was going to install windows 2003 Server and use VMware...but again,... (1 Reply)
Discussion started by: Fatflea
1 Replies
6. UNIX for Dummies Questions & Answers
I have 2 Dell Poweredge 1950 servers running . I have been having intermittent performance issues with the NIC cards on one of them. The two servers are identical and are running the same operating system. The server that has the issue is on the DMZ on a a static IP and is hosting a website. ... (0 Replies)
Discussion started by: skotapal
0 Replies
7. SCO
Hello all,
I'am experiencing weird relyability problems with a SCO 6.0 Openserver server that runs on a Dell Poweredge 1800 equipped with a PERC DC4 raid controller and 4 36 GB 15 K rpm hot swappable scsi harddisks.
It runs a RAID 10 configuration.
It uses the mega hba, Revision 8.03a Release... (1 Reply)
Discussion started by: frederik1
1 Replies
8. Programming
Hi,
I have a C++ program to access /dev/mem and retrieve details like Vendor, Manufacturer details of the motherboard. This works fine on all the machines except for on Dell Poweredge 2850,1950... machines.
I receive a 'EFAULT' when I try to access /dev/mem on these servers.
I suspect some... (1 Reply)
Discussion started by: ragisreekanth
1 Replies
LEARN ABOUT XFREE86
backup_apropos
BACKUP_APROPOS(8) AFS Command Reference BACKUP_APROPOS(8)
NAME
backup_apropos - Displays each help entry containing a keyword string
SYNOPSIS
backup apropos -topic <help string> [-help]
backup ap -t <help string> [-h]
DESCRIPTION
The backup apropos command displays the first line of the online help entry for any backup command that has in its name or short
description the string specified by the -topic argument.
To display the syntax for a command, use the backup help command.
OPTIONS
-topic <help string>
Specifies the keyword string to match, in lowercase letters only. If the string is more than a single word, surround it with double
quotes (" ") or other delimiters.
-help
Prints the online help for this command. All other valid options are ignored.
OUTPUT
The first line of a command's online help entry names it and briefly describes its function. This command displays the first line for any
backup command where the string specified with the -topic argument is part of the command name or first line.
EXAMPLES
The following example lists all backup commands that include the word "tape" in their names or short descriptions:
% backup apropos tape
labeltape: label a tape
readlabel: read the label on tape
scantape: dump information recovery from tape
status: get tape coordinator status
PRIVILEGE REQUIRED
None
SEE ALSO
backup(8), backup_help(8)
COPYRIGHT
IBM Corporation 2000. <http://www.ibm.com/> All Rights Reserved.
This documentation is covered by the IBM Public License Version 1.0. It was converted from HTML to POD by software written by Chas
Williams and Russ Allbery, based on work by Alf Wachsmann and Elizabeth Cassell.
OpenAFS 2012-03-26 BACKUP_APROPOS(8)