Dell PowerEdge 2600 tape backup Post: 302374513

8 More Discussions You Might Find Interesting

1. Linux Benchmarks

Dell Dual Xeon PowerEdge 4600

Notes: System Configuration: Dell Computer Corporation PowerEdge 4600 (4 X Intel(R) XEON(TM) CPU 2.00GHz 1988.782 MHz) hyperthreaded System clock frequency: 99.0827 MHz Memory size (approximate): 2559 Megabytes ========================= CPUs ======================== CPU # CPU...

2. Linux Benchmarks

Dell Poweredge 2400 / 533

CPU/Speed: Dual PIII 533 Ram: 256Mb PC133 Motherboard: Unknown, Intel Chipset Cache: 256k on board Controller: PARC Raid 2/Si, AIC-7880U Disk: 30Gb RAID 5 Load: 1 user. Clean boot, init 5 but X-Windows not loaded. Kernel: See Benchmarks. pgms: gcc 3.2.3 ...

3. Solaris

Installing Solaris 10 on Dell PowerEdge 2800

hi, i am trying to install solaris 10 (on 4 cd's downloaded from the sun website) on my dell poweredge 2800 server. 2 xeon processors, 2GB of RAM and 2 NICS, 73 GB SCSI (maxtor ultra320, 3.5 series), i can give more details on request... the installation crashes when trying to detect the NICS...

4. Red Hat

Installing RedHat 8.0 onto Dell PowerEdge SC1425 - hdc: status error: status = 0x58

I have successfully installed RedHat 8.0 onto a Dell PowerEdge SC1425 today. This server has two SATA hard drives, and an IDE DVD-ROM drive. Using the following kernel parameters, i successfully installed across both hard drives from CD: ide0=0x1f0,0x3f6,14 vga=791 resolution=1024x768 expert...

5. Filesystems, Disks and Memory

Linux and Dell 1500sc Poweredge Server

Does anybody no how to get around the fact that the Red Hat installation does not see the SCSI hard drives. It lets you manually pick the proper device, but still fails saying no drive detected (or something to that effect). I was going to install windows 2003 Server and use VMware...but again,...

6. UNIX for Dummies Questions & Answers

Stange problem Dell PowerEdge 1950/ Boradcom Netextreme NIC

I have 2 Dell Poweredge 1950 servers running . I have been having intermittent performance issues with the NIC cards on one of them. The two servers are identical and are running the same operating system. The server that has the issue is on the DMZ on a a static IP and is hosting a website. ...

7. SCO

Continueing relyability problems with SCO 6.0 on Dell Poweredge 1800 with PERC DC4.

Hello all, I'am experiencing weird relyability problems with a SCO 6.0 Openserver server that runs on a Dell Poweredge 1800 equipped with a PERC DC4 raid controller and 4 36 GB 15 K rpm hot swappable scsi harddisks. It runs a RAID 10 configuration. It uses the mega hba, Revision 8.03a Release...

8. Programming

/dev/mem on Dell Poweredge

Hi, I have a C++ program to access /dev/mem and retrieve details like Vendor, Manufacturer details of the motherboard. This works fine on all the machines except for on Dell Poweredge 2850,1950... machines. I receive a 'EFAULT' when I try to access /dev/mem on these servers. I suspect some...

LEARN ABOUT DEBIAN

tapeinfo

TAPEINFO(1)						      General Commands Manual						       TAPEINFO(1)

NAME

       tapeinfo - report SCSI tape device info

SYNOPSIS

       tapeinfo -f <scsi-generic-device>

DESCRIPTION

       The  tapeinfo  command  reads  various information from SCSI tape drives that is not generally available via most vendors' tape drivers. It
       issues raw commands directly to the tape drive, using either the  operating  system's  SCSI  generic  device  (	e.g.  /dev/sg0	on  Linux,
       /dev/pass0 on FreeBSD) or the raw SCSI I/O ioctl on a tape device on some operating systems.

       One  good  time	to  use 'tapeinfo' is immediately after a tape i/o operation has failed. On tape drives that support HP's 'tapealert' API,
       'tapeinfo' will report a more exact description of what went wrong.

       Do be aware that 'tapeinfo' is not a substitute for your operating system's own 'mt' or similar tape driver control program. It is intended
       to supplement, not replace, programs like 'mt' that access your operating system's tape driver in order to report or set information.

OPTIONS

       The first argument, given following -f , is the SCSI generic device corresponding to your tape drive.  Consult your operating system's doc-
       umentation for more information (for example, under Linux these are generally start at /dev/sg0 under FreeBSD these start at /dev/pass0).

       Under FreeBSD, 'camcontrol devlist' will tell you what SCSI devices you have, along with which 'pass' device controls  them.  Under  Linux,
       "cat /proc/scsi/scsi" will tell you what SCSI devices you have.

BUGS AND LIMITATIONS

       This program has only been tested on Linux with a limited number of tape drives (HP DDS4, Seagate AIT).

AVAILABILITY

       tapeinfo  is  currently	being maintained by Robert Nelson <robertnelson@users.sourceforge.net> as part of the 'mtx' suite of programs. The
       'mtx' home page is http://mtx.sourceforge.net  and  the	actual	code  is  currently  available	there  and  via  SVN  from  http://source-
       forge.net/projects/mtx.

SEE ALSO

       mt(1),mtx(1),scsitape(1),scsieject(1),loaderinfo(1)

								    TAPEINFO1.0 						       TAPEINFO(1)