11-24-2009
Compare the contents of /etc/conf/cf.d/mscsi with the actual scsi hardware configuration.
You should be getting some scsi information during POST.
Then either change the hardware to match the configuration, or run "mkdev tape" to add the tape. You will have to relink the kernel to if you have to add the tape, which also will entail a re-boot. The windows access could be NFS, or Samba, or Visionfs which came bundled with the OS.
Last edited by jgt; 11-24-2009 at 07:17 PM..
8 More Discussions You Might Find Interesting
1. Linux Benchmarks
Notes:
System Configuration: Dell Computer Corporation PowerEdge 4600 (4 X Intel(R) XEON(TM) CPU 2.00GHz
1988.782 MHz) hyperthreaded
System clock frequency: 99.0827 MHz
Memory size (approximate): 2559 Megabytes
========================= CPUs ========================
CPU # CPU... (0 Replies)
Discussion started by: tnorth
0 Replies
2. Linux Benchmarks
CPU/Speed: Dual PIII 533
Ram: 256Mb PC133
Motherboard: Unknown, Intel Chipset
Cache: 256k on board
Controller: PARC Raid 2/Si, AIC-7880U
Disk: 30Gb RAID 5
Load: 1 user. Clean boot, init 5 but X-Windows not loaded.
Kernel: See Benchmarks.
pgms: gcc 3.2.3
... (2 Replies)
Discussion started by: Garp
2 Replies
3. Solaris
hi, i am trying to install solaris 10 (on 4 cd's downloaded from the sun website) on my dell poweredge 2800 server. 2 xeon processors, 2GB of RAM and 2 NICS, 73 GB SCSI (maxtor ultra320, 3.5 series), i can give more details on request...
the installation crashes when trying to detect the NICS... (0 Replies)
Discussion started by: xinugeek
0 Replies
4. Red Hat
I have successfully installed RedHat 8.0 onto a Dell PowerEdge SC1425 today. This server has two SATA hard drives, and an IDE DVD-ROM drive.
Using the following kernel parameters, i successfully installed across both hard drives from CD:
ide0=0x1f0,0x3f6,14 vga=791 resolution=1024x768 expert... (5 Replies)
Discussion started by: fishsponge
5 Replies
5. Filesystems, Disks and Memory
Does anybody no how to get around the fact that the Red Hat installation does not see the SCSI hard drives. It lets you manually pick the proper device, but still fails saying no drive detected (or something to that effect). I was going to install windows 2003 Server and use VMware...but again,... (1 Reply)
Discussion started by: Fatflea
1 Replies
6. UNIX for Dummies Questions & Answers
I have 2 Dell Poweredge 1950 servers running . I have been having intermittent performance issues with the NIC cards on one of them. The two servers are identical and are running the same operating system. The server that has the issue is on the DMZ on a a static IP and is hosting a website. ... (0 Replies)
Discussion started by: skotapal
0 Replies
7. SCO
Hello all,
I'am experiencing weird relyability problems with a SCO 6.0 Openserver server that runs on a Dell Poweredge 1800 equipped with a PERC DC4 raid controller and 4 36 GB 15 K rpm hot swappable scsi harddisks.
It runs a RAID 10 configuration.
It uses the mega hba, Revision 8.03a Release... (1 Reply)
Discussion started by: frederik1
1 Replies
8. Programming
Hi,
I have a C++ program to access /dev/mem and retrieve details like Vendor, Manufacturer details of the motherboard. This works fine on all the machines except for on Dell Poweredge 2850,1950... machines.
I receive a 'EFAULT' when I try to access /dev/mem on these servers.
I suspect some... (1 Reply)
Discussion started by: ragisreekanth
1 Replies
st(1M) st(1M)
NAME
st - shared tape administration
SYNOPSIS
device_file
DESCRIPTION
The command provides users with a command-line interface to check the status of a shared tape device or to reclaim a shared tape device
from a host system that has failed while holding a reservation on the shared tape device. The command can also be used for the same pur-
pose on shared library robotic devices. To use the command you must have root user id.
Please see examples below for usage.
Options
recognizes the following options and arguments:
Specifies the tape device file or sctl/esctl pass-through device
file for the shared tape/library device. This parameter is mandatory and will report an error if device_file is omitted.
Allows the user to reclaim a shared tape device or shared
library robotic device in the case where a host failed while holding a reservation on the shared device. This option causes
a bus device reset to be issued to the device specified by the option.
Prints out the current status of the shared tape/library
device specified by the option.
RETURN VALUE
returns 0 upon successful completion and 1 otherwise.
EXAMPLES
The following shows three examples of output from the above command.
The above output indicates that the shared device is reserved by another host and is therefore unavailable at this time.
The above output indicates that the shared device is not ready for use at this time.
The above output indicates that the shared device is ready for use at this time.
To reclaim a shared tape/library device from a failed host, the following command can be used:
WARNINGS
The option must be used with care. When reclaiming devices, it must be ensured that the host from which the device is being reclaimed has
in fact failed, as data may be lost as the result of reclaiming a device that is currently in use by another host.
AUTHOR
was developed by Hewlett-Packard.
SEE ALSO
mt(1), scsi(7), scsi_ctl(7).
st(1M)