Using HP-UX v11
Need to monitor cpu and memory usage, total for system and separately for each user in command-line mode.
Found out next ways to monitor total cpu usage under hp-ux:
1) vmstat, also shows free memory
2) sar -M
ps -eo user,pcpu - does not work, means 'user-defined format'... (4 Replies)
I am trying to write a small (and rather simple) script to gather some info about the system and piping it to dzen2
first, i want to explain some things.
I know i could have used conky, but my intention was to expand my knowledge of bash, pipes and redirections inside a script, and to have fun... (14 Replies)
how can I find cpu usage memory usage swap usage and
I want to know CPU usage above X% and contiue Y times and memory usage above X % and contiue Y times
my final destination is monitor process
logical volume usage above X % and number of Logical voluage above
can I not to... (3 Replies)
Hi,
How can I find total CPU usage in percentage? e.g. if my system has 8 CPUs and I want to list total usage for all of them, is it possible through a command?
I have tried some of the commands like top, mpstat, sar. The output of those commands has to be manipulated to derive the percentage... (14 Replies)
Hi Experts,
I am executing multiple instances(in parallel) of perl script on HP-UX box.
OS is allocating substantial amount of CPU to these perl processes,resulting higher cpu utilization.
Glance always shows perl processes are occupying majority of the CPU resource. It is causing slower... (2 Replies)
Hi All,
I have a script which does report the cpu usuage, there are few output parameter/fields displayed from the script. My problem is I have monitor the output and decide
which cpu number (column 2) has maximum value (column 6).
Since the output is displayed/updated every seconds, it's very... (1 Reply)
Hello Friends,
I am trying to create a shell script which will check the CPU utilization. I use command top to check the %CPU usage. It give s me below output
Cpu states:
CPU LOAD USER NICE SYS IDLE BLOCK SWAIT INTR SSYS
0 0.31 9.6% 0.0% 6.1% 84.3% 0.0% 0.0%... (3 Replies)
Hi all
I was wondering if its possible to write a script to keep CPU usage at 90%-95%? for a single cpu linux server?
I have a perl script I run on servers with multple cpu's and all I do is max all but one cpu to get into the 90'% utilised area. I now need a script that raises the CPU to... (4 Replies)
Hi,
Recently i have write a simple script to capture CPU high usage based on prstat but i found out that it did capture correctly. I need to capture the rows that contains CPU usage more than 3%. Below line which i thought will capture CPU usage based CPU column in prstat(9th parameter) which is... (3 Replies)
Discussion started by: tharmendran
3 Replies
LEARN ABOUT OSF1
iostat
iostat(1) General Commands Manual iostat(1)NAME
iostat - Reports I/O statistics
SYNOPSIS
iostat [drive...] [interval] [count]
OPERANDS
Forces iostat to display specific drives. If drive is not specified (or the specified drive does not exist on the system or cluster,
iostat displays the first two drives (even if more than two disk drives are configured in the system). Causes iostat to report once each
interval seconds. The first report is for all time since the system was last booted, and each subsequent report is for the last interval
only.The value must not be 0. Specifies the number of reports. For example, iostat 1 10 would produce 10 reports at 1-second intervals.
You cannot specify count without interval because the first numeric argument to iostat is assumed to be interval.
DESCRIPTION
The iostat command reports the following information: For terminals (collectively), the number of characters read and written per second.
For each disk, the number of transfers per second and bytes transferred per second (in kilobytes). For the system, the percentage of time
the system has spent in user mode, in user mode running low priority (nice) processes, in system mode, and idling.
To compute this information, iostat counts data transfer completions, the number of words transferred for each disk, and the collective
number of input and output characters for terminals. Also, each sixtieth of a second, iostat examines the state of each disk and makes a
tally if the disk is active.
When you issue an iostat command on a cluster member, it displays statistics only for those disks that are local to the member and that
member's usage of those shared disks that it has mounted. It displays 0 for other disks in the cluster (those it doesn't have mounted),
regardless of whether they are on the shared bus or are local to some other member.
EXAMPLES
The output from this example displays cpu, terminal, and disk statistics for the first two disks on the system providing 5 reports at 1
second intervals:
# iostat 1 5
tty floppy1 dsk9 cpu
tin tout bps tps bps tps us ni sy id
0 3 0 0 0 0 1 0 4 95
4 58 0 0 0 0 1 0 2 97
1 53 0 0 0 0 0 0 2 98
5 59 0 0 0 0 1 0 1 98
6 60 0 0 0 0 1 0 2 97
The second example specifies device names in the command:
# iostat dsk2 dsk3 cdrom2
tty dsk2 cdrom2 dsk3 cpu
tin tout bps tps bps tps bps tps us ni sy id
0 13 11 5 5 2 2427 1213 0 1 1 98
SEE ALSO Commands:vmstat(1)iostat(1)