Try
As it was written above it means: assign the value of var to limit. The value of limit determines the outcome, if more than 0 then the outcome is true.
Last edited by Scrutinizer; 11-24-2009 at 05:05 PM..
Hi all,
I am working on a c source code nearly 2000 line . it contains one big for( i=0; i< 200 ; i++ ) loop of around 600 lines
could any tell me how to break the execution of prog when the value of i is 50 in for loop so that i can check
inside the loop.
Thanks.. (1 Reply)
It is happening with my sessions already second time: a 'for'-loop for some reason stop to work as expected.
That means or it is looping without exitting, or it is not loop even once.
Here example of my try when it is not processing even one loop.
You can see, I start new subshell and... (14 Replies)
Hi All,
I am comparing two strings inside an if condition if the strings are same then it should go inside the loop else it should execute code given in else part.
But there is a but inside my script
Even if the if condition is true
it is not going inside the loop also it is executing... (4 Replies)
I'm trying to understand if it's possible to create a set of variables that are numbered based on another variable (using eval) in a loop, and then call on it before the loop ends.
As an example I've written a script called question (The fist command is to show what is the contents of the... (2 Replies)
Hi everyone - just like to say great forum...I've learned a lot off here but I just can't figure this one out...(first post)
I'm writing a script to monitor a directory and email the latest modified file....(I realize there are better ways than I'm trying here...I don't like copying and pasting... (5 Replies)
I wonder how to stop further loop iterations when conditions gets false e.g.
This file.txt contains the following structure :
1
2
3
4
5
6
7
8
9
10
How to stop iteration when if statement gets false ?
for n in `cat file.txt`
do
if (( n<=5 )) (1 Reply)
Hey guys,
How do I make a loop that reads all the parameters en then stop when there are no parameters anymore ?
Something that gives an output like this:
./Script.sh parameter1 parameter2 parameter3
parameter = parameter1
parameter = parameter2
parameter = parameter3
Thanks a lot,... (5 Replies)
Hi all,
i am trying to process a list of values in FILE like this:
aaa:bbb
ccc:ddd
eee:fff
With the following logic:
for INFO in FILE
do
export F1=`cut -f1,3,5,7 -d":" < FILE`
export F2=`cut -f2,3,5,7 -d":" < FILE`
ssh $F1 bash <<EOF
echo $F1
echo $F2
date (10 Replies)
Im unable to stop the below infinite loop (bash script). Can someone tell me why this isnt responding to signals eg: ctrl+c (SIGINT) or ctrl+z
c=0
test_loop() {
c=$(($c+1))
echo "count value is : $c "
sleep 1
test_loop
}
Im using: SunOS 5.10
PS: If run this as... (13 Replies)
Here's my code:
awk -F '' 'NR==FNR {
if (/time/ && $5>10)
A=$2" "$3":"$4":"($5-01)
else if (/time/ && $5<01)
A=$2" "$3":"$4-01":"(59-$5)
else if (/time/ && $5<=10)
A=$2" "$3":"$4":0"($5-01)
else if (/close/) {
B=0
n1=n2;
... (2 Replies)
Discussion started by: klane
2 Replies
LEARN ABOUT LINUX
irsend
IRSEND(1) User Commands IRSEND(1)NAME
irsend - basic LIRC program to send infra-red commands
SYNOPSIS
irsend [options] DIRECTIVE REMOTE CODE [CODE...]
DESCRIPTION
Asks the lircd daemon to send one or more CIR (Consumer Infra-Red) commands. This is intended for remote control of electronic devices such
as TV boxes, HiFi sets, etc.
DIRECTIVE can be:
SEND_ONCE - send CODE [CODE ...] once
SEND_START - start repeating CODE
SEND_STOP - stop repeating CODE
LIST - list configured remote items
SET_TRANSMITTERS - set transmitters NUM [NUM ...]
SIMULATE - simulate IR event
REMOTE is the name of a remote, as described in the lircd configuration file.
CODE is the name of a remote control key of REMOTE, as it appears in the lircd configuration file.
NUM is the transmitter number of the hardware device.
For the LIST DIRECTIVE, REMOTE and/or CODE can be empty:
LIST "" "" - list all configured remote names
LIST REMOTE "" - list all codes of REMOTE
LIST REMOTE CODE - list only CODE of REMOTE
The SIMULATE command only works if it has been explicitly enabled in lircd.
-h --help
display usage summary
-v --version
display version
-d --device
use given lircd socket [/var/run/lirc/lircd]
-a --address=host[:port]
connect to lircd at this address
-# --count=n
send command n times
EXAMPLES
irsend LIST DenonTuner ""
irsend SEND_ONCE DenonTuner PROG-SCAN
irsend SEND_ONCE OnkyoAmpli VOL-UP VOL-UP VOL-UP VOL-UP
irsend SEND_START OnkyoAmpli VOL-DOWN ; sleep 3
irsend SEND_STOP OnkyoAmpli VOL-DOWN
irsend SET_TRANSMITTERS 1
irsend SET_TRANSMITTERS 1 3 4
irsend SIMULATE "0000000000000476 00 OK TECHNISAT_ST3004S"
FILES
/etc/lirc/lircd.conf
Default lircd configuration file. It should contain all the remotes, their infra-red codes and the corresponding timing and wave-
form details.
DIAGNOSTICS
If lircd is not running (or /var/run/lirc/lircd lacks write permissions) irsend aborts with the following diagnostics:
"irsend: could not connect to socket"
"irsend: Connection refused" (or "Permission denied").
SEE ALSO
The documentation for lirc is maintained as html pages. They are located under html/ in the documentation directory.
lircd(8), mode2(1), smode2(1), xmode2(1), irrecord(1), irw(1), http://www.lirc.org.
irsend 0.9.0-pre1 October 2010 IRSEND(1)