I have to process a data file in Ab Initio. This data file is pipe delimited. BUt the file may have a Disclaimer line at the end. So before picking it for processing, I need to check if this line is there I need to remove it. ANy suggestions.
Thanks
Shalu (1 Reply)
I have a file with one of the following lines, when opened with vi
33560010686GPT£120600GBPGBP10082007DS
In the above line, I want to get rid of the junk character before the £ (pound sysmbol).
When I tried copying £ from windows and copy in unix vi, it prints as £ and I tried pattern replace... (2 Replies)
A sed command works most of the time however it fails sometimes.
I put each line (record) I read of a file through the following command
data=$(cat file | sed 's///g' | sed 's|.*ex:Msg\(.*\)ex:Msg.*|\1|' )
When I run the script I get a message that states that there is an invalid format... (6 Replies)
Dear All,
I need a unix script that will read the 7th line and especially these fileds from a file Mo speed 16, Mt speed 15 every 15 minutes starting from 00:00 to 23:45 on daily basis and put the result in a txt file and name it MT_MO_20090225.txt, please also note that the system date format... (2 Replies)
Hello.
I'm using a file to "grep" in a 2nd one (with awk)
cat file1
2 first user
9 second user
1 third user (with a space after user)
I want to get the line except the 1st field so I do :
field=$(gawk '{$1 =""; print $0}' file | sed 's/^ //')
It works but it deletes... (5 Replies)
Hi All,
Was wondering how I can do the following....
I have a String as follows
"ACCTRL000005022RRWDKKEEDKDD...."
This string can be in a file called tail.out or in a Variable called $VAR2
Now I have another variable called $VAR1="000004785" (9 bytes long), I need the content of... (5 Replies)
I have a file with different record length. The file as to be converted into fixed length by appending spaces at the end of record. The length should be calculated based on the record with maximum length in the file.
If the length is less than the max length, the spaces should be appended... (4 Replies)
Hi friend,
I have one file , and i want to read that file character by character.
I need this script in ksh.
while using read option with -n1 am getting error.
while read -n1 c read has bad option
And if i am using below script, then if in a line has space like this ( Pallvi mahajan)... (10 Replies)
Hi:)
I have a large file ( couple thousand lines ) and I'm trying to add a character after the first word/space on each line.
eg:
First line of text
Second line of text
Third line of text
Fourth line of text
Fifth line of text
I'd like to accomplish:
First - line of text
Second... (8 Replies)
Hi all,
I am looking for to filter out based on 7th character and list the number of occurrence based on the 7th character if p , d , o or m
1. if 7th character is p , Output should be: p_hosts = N
2. if 7th character is d , Output should be: d_hosts = N
3. if 7th character is o , Output... (10 Replies)
Discussion started by: rveri
10 Replies
LEARN ABOUT SUSE
irsend
IRSEND(1) FSF IRSEND(1)NAME
irsend - basic LIRC program to send infra-red commands
SYNOPSIS
irsend [options] DIRECTIVE REMOTE CODE [CODE...]
DESCRIPTION
Asks the lircd daemon to send one or more CIR (Consumer Infra-Red) commands. This is intended for remote control of electronic devices such
as TV boxes, HiFi sets, etc.
DIRECTIVE can be:
SEND_ONCE - send CODE [CODE ...] once
SEND_START - start repeating CODE
SEND_STOP - stop repeating CODE
LIST - list configured remote items
SET_TRANSMITTERS - set transmitters NUM [NUM ...]
SIMULATE - simulate IR event
REMOTE is the name of a remote, as described in the lircd configuration file.
CODE is the name of a remote control key of REMOTE, as it appears in the lircd configuration file.
NUM is the transmitter number of the hardware device.
For the LIST DIRECTIVE, REMOTE and/or CODE can be empty:
LIST "" "" - list all configured remote names
LIST REMOTE "" - list all codes of REMOTE
LIST REMOTE CODE - list only CODE of REMOTE
The SIMULATE command only works if it has been explicitly enabled in lircd.
-h --help
display usage summary
-v --version
display version
-d --device
use given lircd socket [/var/run/lirc/lircd]
-a --address=host[:port]
connect to lircd at this address
-# --count=n
send command n times
EXAMPLES
irsend LIST DenonTuner ""
irsend SEND_ONCE DenonTuner PROG-SCAN
irsend SEND_ONCE OnkyoAmpli VOL-UP VOL-UP VOL-UP VOL-UP
irsend SEND_START OnkyoAmpli VOL-DOWN ; sleep 3
irsend SEND_STOP OnkyoAmpli VOL-DOWN
irsend SET_TRANSMITTERS 1
irsend SET_TRANSMITTERS 1 3 4
irsend SIMULATE "0000000000000476 00 OK TECHNISAT_ST3004S"
FILES
/etc/lirc/lircd.conf
Default lircd configuration file. It should contain all the remotes, their infra-red codes and the corresponding timing and wave-
form details.
DIAGNOSTICS
If lircd is not running (or /var/run/lirc/lircd lacks write permissions) irsend aborts with the following diagnostics:
"irsend: could not connect to socket"
"irsend: Connection refused" (or "Permission denied").
SEE ALSO
The documentation for lirc is maintained as html pages. They are located under html/ in the documentation directory.
lircd(8), mode2(1), smode2(1), xmode2(1), irrecord(1), irw(1), http://www.lirc.org.
irsend 0.8.7pre1 May 2010 IRSEND(1)