the en and et devices are being generated when you assign an ip-adress, the ent device ist available when you configure the adapter on the hmc. (for lpars) or plug it physically in and run cfgmgr or reboot.
you can remove the en and et device
the entx device resides on the system
if you want to leave the entries in the odm, use
but don't run cfgmgr or reboot the machine then
I have installed in the server a quad ethernet adapter, I'm using two interfaces with two different IP networks, both interfaces are connected to a switch, the switch report that is receiving the same MAC address in both ports so must of the times I have connectivity problems.
Any idea to change... (1 Reply)
I have a Dual Boot system - XP with Solaris 10. I built the system from the ground up with different components and the Ethernet Card built into the Motherboard is a Marvell Yukon Gigabit Ethernet 10/100/1000 T-base, RJ-45 Copper.
I am unable to go to the Web as the Ethernet Card is still not... (2 Replies)
All
I am trying allocate an IVE to an LPAR (not a VIO) running AIX 7.1. I am getting the error:
HSCL068A
Explanation
Logical port can not be assigned to Logical Partition because this Logical Partition is not the promiscuous LPAR for the physical port.
Has anyone encountered this... (1 Reply)
Hi,
I have installed Oracle Enterprise Linux 5 in my PC. After the installation the Ethernet Card is not got detected.
But I could able to get the details using the command lspci -a:
01:00.0 Ethernet controller: Attansic Technology Corp. L1 Gigabit Ethernet Adapter (rev b0).
But I could... (4 Replies)
Good morning,
Saw this on a system this morning, thought I'd check with this group before calling IBM.
Basically what we have here is a P7 running 6.1 reporting the following in errpt:
LABEL: GOENT_LINK_DOWN
IDENTIFIER: EC0BCCD4
This is for ent4, which is odd because we... (0 Replies)
Hi,
Does anybody have a "Sun 10-Gigabit Ethernet Adapter installation CD" or driver ixge for Sun 10-Gigabit Ethernet PCI-X adapter? I need it but can't find it anywhere. So if you know where I can download it or purchase it, please let me know. (Already tried Oracle's website, don't have it) ... (5 Replies)
Hi Techies,
I have a doubt.
ent0 Available Logical Host Ethernet Port (lp-hea)
ent1 Available Logical Host Ethernet Port (lp-hea)
ent2 Available Logical Host Ethernet Port (lp-hea)
ent3 Available Logical Host Ethernet Port (lp-hea)
ent4 Available... (4 Replies)
Hi Community,
i have one issue with 10 fiber ethernet adapter.
here is my details:
root@new-bpel.example.com #dladm show-dev
bge0 link: unknown speed: 0 Mbps duplex: unknown
bge1 link: up speed: 1000 Mbps duplex: full
qlge2 link:... (4 Replies)
Hello community, I have a Proliant HP DL380P with the following network adapters:
NetXtreme BCM5719 Gigabit Ethernet PCIe (Ethernet 1Gb 4-port 331FLR Adapter)
82580 Gigabit Network Connection (NC365T 4-port Ethernet Server Adapter)
I installed Red Hat 7.2 but it recognizes only the... (9 Replies)
Discussion started by: Lord Spectre
9 Replies
LEARN ABOUT SUNOS
reboot
reboot(3C)reboot(3C)NAME
reboot - reboot system or halt processor
SYNOPSIS
#include <sys/reboot.h>
int reboot(int howto, char *bootargs);
The reboot() function reboots the system. The howto argument specifies the behavior of the system while rebooting and is a mask con-
structed by a bitwise-inclusive-OR of flags from the following list:
RB_AUTOBOOT The machine is rebooted from the root filesystem on the default boot device. This is the default behavior. See boot(1M) and
kernel(1M).
RB_HALT The processor is simply halted; no reboot takes place. This option should be used with caution.
RB_ASKNAME Interpreted by the bootstrap program and kernel, causing the user to be asked for pathnames during the bootstrap.
RB_DUMP The system is forced to panic immediately without any further processing and a crash dump is written to the dump device
(see dumpadm(1M)) before rebooting.
Any other howto argument causes the kernel file to boot.
The interpretation of the bootargs argument is platform-dependent.
Upon successful completion, reboot() never returns. Otherwise, -1 is returned and errno is set to indicate the error.
The reboot() function will fail if:
EPERM The {PRIV_SYS_CONFIG} privilege is not asserted in the effective set of the calling process.
intro(1M), boot(1M), dumpadm(1M), halt(1M), init(1M), kernel(1M), reboot(1M), uadmin(2)
22 Mar 2004 reboot(3C)