11-18-2009
Temporarily disabling unused ethernet adapter
Hi,
In our AIX 5.2 server , we have one unused ethernet adapter which doesn't have cable connection . For this interface , we are getting alerts in errpt .
Could you suggesthow to stop this alert ? And sametime i would like to keep this device in ODM .
Is there anyway to change the state of device from "Available" to "Stopped" ?
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
I have installed in the server a quad ethernet adapter, I'm using two interfaces with two different IP networks, both interfaces are connected to a switch, the switch report that is receiving the same MAC address in both ports so must of the times I have connectivity problems.
Any idea to change... (1 Reply)
Discussion started by: mono673
1 Replies
2. Solaris
I have a Dual Boot system - XP with Solaris 10. I built the system from the ground up with different components and the Ethernet Card built into the Motherboard is a Marvell Yukon Gigabit Ethernet 10/100/1000 T-base, RJ-45 Copper.
I am unable to go to the Web as the Ethernet Card is still not... (2 Replies)
Discussion started by: tubbyrana
2 Replies
3. Solaris
hi all,
How to install onboard ethernet card on Sun SPARC M4000 server? (3 Replies)
Discussion started by: Tlg13team
3 Replies
4. AIX
All
I am trying allocate an IVE to an LPAR (not a VIO) running AIX 7.1. I am getting the error:
HSCL068A
Explanation
Logical port can not be assigned to Logical Partition because this Logical Partition is not the promiscuous LPAR for the physical port.
Has anyone encountered this... (1 Reply)
Discussion started by: johnf
1 Replies
5. Red Hat
Hi,
I have installed Oracle Enterprise Linux 5 in my PC. After the installation the Ethernet Card is not got detected.
But I could able to get the details using the command lspci -a:
01:00.0 Ethernet controller: Attansic Technology Corp. L1 Gigabit Ethernet Adapter (rev b0).
But I could... (4 Replies)
Discussion started by: chidhu.anu
4 Replies
6. AIX
Good morning,
Saw this on a system this morning, thought I'd check with this group before calling IBM.
Basically what we have here is a P7 running 6.1 reporting the following in errpt:
LABEL: GOENT_LINK_DOWN
IDENTIFIER: EC0BCCD4
This is for ent4, which is odd because we... (0 Replies)
Discussion started by: Michael Mullig
0 Replies
7. Hardware
Hi,
Does anybody have a "Sun 10-Gigabit Ethernet Adapter installation CD" or driver ixge for Sun 10-Gigabit Ethernet PCI-X adapter? I need it but can't find it anywhere. So if you know where I can download it or purchase it, please let me know. (Already tried Oracle's website, don't have it) ... (5 Replies)
Discussion started by: Lhao
5 Replies
8. AIX
Hi Techies,
I have a doubt.
ent0 Available Logical Host Ethernet Port (lp-hea)
ent1 Available Logical Host Ethernet Port (lp-hea)
ent2 Available Logical Host Ethernet Port (lp-hea)
ent3 Available Logical Host Ethernet Port (lp-hea)
ent4 Available... (4 Replies)
Discussion started by: jayadeava
4 Replies
9. Solaris
Hi Community,
i have one issue with 10 fiber ethernet adapter.
here is my details:
root@new-bpel.example.com #dladm show-dev
bge0 link: unknown speed: 0 Mbps duplex: unknown
bge1 link: up speed: 1000 Mbps duplex: full
qlge2 link:... (4 Replies)
Discussion started by: bentech4u
4 Replies
10. Red Hat
Hello community, I have a Proliant HP DL380P with the following network adapters:
NetXtreme BCM5719 Gigabit Ethernet PCIe (Ethernet 1Gb 4-port 331FLR Adapter)
82580 Gigabit Network Connection (NC365T 4-port Ethernet Server Adapter)
I installed Red Hat 7.2 but it recognizes only the... (9 Replies)
Discussion started by: Lord Spectre
9 Replies
SET_NET_DEFAULT(8) System Manager's Manual SET_NET_DEFAULT(8)
NAME
s_n_d, set_net_default - select the default TCP/IP network
SYNOPSIS
set_net_default: not found
DESCRIPTION
This manual page is here because so many others refer to it. The set_net_default command does not exist under standard Minix, because the
TCP/IP server only supports one network. The server under Minix-vmd supports four different networks, that can each be chosen as the
default network.
The TCP/IP library and commands do have a notion about a "default network" however, because the code is shared between the Minix versions.
So if you want to venture into network programming then you should know about the devices and environment variables mentioned below to make
your program compatible. (Especially since there is a plan to upgrade the TCP/IP server for standard Minix.)
Options and environment to change the default
Many TCP/IP programs implement the following options and environment variables to change the default devices set by set_net_default. The
options are only implemented for low level programs where it makes sense to name a network device. The environment variables are used in
all code. You can run a process and all its children connected to a different network by setting four environment variables.
ETH_DEVICE=device
-E device
Device to use as raw ethernet device instead of the default /dev/eth.
PSIP_DEVICE=device
-P device
Pseudo IP device to use instead of /dev/psip.
IP_DEVICE=device
-I device
IP device to use instead of /dev/ip.
TCP_DEVICE=device
-T device
TCP device to use.
UDP_DEVICE=device
-U device
UDP device to use.
FILES
/dev/eth[01] First and second raw ethernet.
/dev/psip[01] First and second Pseudo IP network.
/dev/ip[0123] IP devices for two ethernets and two Pseudo IP networks.
/dev/tcp[0123] TCP devices for same four networks.
/dev/udp[0123] UDP devices.
/dev/eth, /dev/psip, /dev/ip, /dev/tcp, /dev/udp
Devices for the default network, links to the devices above. Eth is only present if ethernet is the default, psip only
for pseudo IP.
SEE ALSO
ip(4), boot(8).
AUTHOR
Kees J. Bot (kjb@cs.vu.nl)
SET_NET_DEFAULT(8)