11-18-2009
Temporarily disabling unused ethernet adapter
Hi,
In our AIX 5.2 server , we have one unused ethernet adapter which doesn't have cable connection . For this interface , we are getting alerts in errpt .
Could you suggesthow to stop this alert ? And sametime i would like to keep this device in ODM .
Is there anyway to change the state of device from "Available" to "Stopped" ?
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
I have installed in the server a quad ethernet adapter, I'm using two interfaces with two different IP networks, both interfaces are connected to a switch, the switch report that is receiving the same MAC address in both ports so must of the times I have connectivity problems.
Any idea to change... (1 Reply)
Discussion started by: mono673
1 Replies
2. Solaris
I have a Dual Boot system - XP with Solaris 10. I built the system from the ground up with different components and the Ethernet Card built into the Motherboard is a Marvell Yukon Gigabit Ethernet 10/100/1000 T-base, RJ-45 Copper.
I am unable to go to the Web as the Ethernet Card is still not... (2 Replies)
Discussion started by: tubbyrana
2 Replies
3. Solaris
hi all,
How to install onboard ethernet card on Sun SPARC M4000 server? (3 Replies)
Discussion started by: Tlg13team
3 Replies
4. AIX
All
I am trying allocate an IVE to an LPAR (not a VIO) running AIX 7.1. I am getting the error:
HSCL068A
Explanation
Logical port can not be assigned to Logical Partition because this Logical Partition is not the promiscuous LPAR for the physical port.
Has anyone encountered this... (1 Reply)
Discussion started by: johnf
1 Replies
5. Red Hat
Hi,
I have installed Oracle Enterprise Linux 5 in my PC. After the installation the Ethernet Card is not got detected.
But I could able to get the details using the command lspci -a:
01:00.0 Ethernet controller: Attansic Technology Corp. L1 Gigabit Ethernet Adapter (rev b0).
But I could... (4 Replies)
Discussion started by: chidhu.anu
4 Replies
6. AIX
Good morning,
Saw this on a system this morning, thought I'd check with this group before calling IBM.
Basically what we have here is a P7 running 6.1 reporting the following in errpt:
LABEL: GOENT_LINK_DOWN
IDENTIFIER: EC0BCCD4
This is for ent4, which is odd because we... (0 Replies)
Discussion started by: Michael Mullig
0 Replies
7. Hardware
Hi,
Does anybody have a "Sun 10-Gigabit Ethernet Adapter installation CD" or driver ixge for Sun 10-Gigabit Ethernet PCI-X adapter? I need it but can't find it anywhere. So if you know where I can download it or purchase it, please let me know. (Already tried Oracle's website, don't have it) ... (5 Replies)
Discussion started by: Lhao
5 Replies
8. AIX
Hi Techies,
I have a doubt.
ent0 Available Logical Host Ethernet Port (lp-hea)
ent1 Available Logical Host Ethernet Port (lp-hea)
ent2 Available Logical Host Ethernet Port (lp-hea)
ent3 Available Logical Host Ethernet Port (lp-hea)
ent4 Available... (4 Replies)
Discussion started by: jayadeava
4 Replies
9. Solaris
Hi Community,
i have one issue with 10 fiber ethernet adapter.
here is my details:
root@new-bpel.example.com #dladm show-dev
bge0 link: unknown speed: 0 Mbps duplex: unknown
bge1 link: up speed: 1000 Mbps duplex: full
qlge2 link:... (4 Replies)
Discussion started by: bentech4u
4 Replies
10. Red Hat
Hello community, I have a Proliant HP DL380P with the following network adapters:
NetXtreme BCM5719 Gigabit Ethernet PCIe (Ethernet 1Gb 4-port 331FLR Adapter)
82580 Gigabit Network Connection (NC365T 4-port Ethernet Server Adapter)
I installed Red Hat 7.2 but it recognizes only the... (9 Replies)
Discussion started by: Lord Spectre
9 Replies
LEARN ABOUT DEBIAN
hobbit-ackinfo.cgi
HOBBIT-ACKINFO.CGI(1) General Commands Manual HOBBIT-ACKINFO.CGI(1)
NAME
hobbit-ackinfo.cgi - Xymon CGI script to acknowledge alerts
SYNOPSIS
hobbit-ackinfo.cgi
DESCRIPTION
hobbit-ackinfo.cgi is invoked as a CGI script via the hobbit-ackinfo.sh CGI wrapper.
hobbit-ackinfo.cgi is used to acknowledge an alert on the Xymon "Critical Systems" view, generated by the hobbit-nkview.cgi(1) utility.
This allows the staff viewing the Critical Systems view to acknowledge alerts with a "Level 1" alert, thereby removing the alert from the
Critical Systems view.
Note that the Level 1 alert generated by the hobbit-ackinfo.cgi utility does NOT stop alerts from being sent.
In a future version of Xymon (after Xymon 4.2), this utility will also be used for acknowledging alerts at other levels.
OPTIONS
--level=NUMBER
Sets the acknowledgment level. This is typically used to force a specific level of the acknowledgment, e.g. a level 1 acknowledge
when called from the Critical Systems view.
--validity=TIME
Sets the validity of the acknowledgment. By default this is taken from the CGI parameters supplied by the user.
--sender=STRING
Logs STRING as the sender of the acknowledgment. By default, this is taken from the loginname of the webuser sending the acknowledg-
ment.
--env=FILENAME
Loads the environment defined in FILENAME before executing the CGI script.
--area=NAME
Load environment variables for a specific area. NB: if used, this option must appear before any --env=FILENAME option.
--debug
Enables debugging output.
ENVIRONMENT VARIABLES
BBHOME Used to locate the template files for the generated web pages.
QUERY_STRING
Contains the parameters for the CGI script.
SEE ALSO
hobbit-nkview.cgi(1), xymon(7)
Xymon Version 4.2.3: 4 Feb 2009 HOBBIT-ACKINFO.CGI(1)