11-13-2009
Quote:
Originally Posted by
jgobbur
Hi,
I am trying to list all the interface present in the given system.
[...]
To list all interfaces in the given system use
# lsdev -c if
or
# lsdev -Cc if
when you are below AIX 5.2.
Use grep to subdivide Defined and Available interfaces. Why do you want to reinvent the wheel?
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hi !
Does anyone know how can i get information about my network interface ... if it works in half or full duplex mode !!
Thx in adivance !
Witt (4 Replies)
Discussion started by: witt
4 Replies
2. Programming
Hello
I have a problem with retreiving network interface list using IOCTLs. I have 4 interfaces:
$ ip addr
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue state UNKNOWN
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
inet6 ::1/128 scope... (1 Reply)
Discussion started by: xyzt
1 Replies
3. AIX
Hi All,
Please let me know the command to restart the network interface and enable it on boot in AIX, similar to /etc/init.d/network restart in Redhat.
Thanks,
Sunil.K
please watch out to post in the right subforum! (9 Replies)
Discussion started by: sunilrk07
9 Replies
4. Solaris
i need to configure a zone to use different interface (bge2) than global and have connected to completely different network switch & to use its own defaultrouter and hosts file .. is it possible ..if so ..how ?
Thanks (9 Replies)
Discussion started by: skamal4u
9 Replies
5. Linux
Hi,
Can any one please help me increase the arp stale time of an ipv6 interface on linux platform ?
I have tried increasing the variable gc_stale_time but that doesnt work.
Thanks (2 Replies)
Discussion started by: dkothapa
2 Replies
6. UNIX and Linux Applications
Hi,
I'm a italian student. For my thesis I develop a gateway with protocol 6lowpan.
For that I must access to network interface to develope my personal stack based on standard 802.15.4.
Can you help me? I need an explanation for that. (0 Replies)
Discussion started by: berny88
0 Replies
7. IP Networking
Hello,
Please what's the difference between:
AND
Thank you so much (3 Replies)
Discussion started by: chercheur857
3 Replies
8. IP Networking
Hello,
Please, how can i create a network interface with a routable IP address on linux (ubuntu) ?
AND
How can i desactivate an interface?
Thank you so much for help. (1 Reply)
Discussion started by: chercheur857
1 Replies
9. Solaris
I've one Netra 240
After changing main board and system configuration card reader, Network is not accessible any more, Network interfaces are always UP and Running even when there is no cable connected to Network interfaces.
I tried to restart and plumb/unplumb with no luck.
ifconfig -a... (7 Replies)
Discussion started by: samer.odeh
7 Replies
10. UNIX for Dummies Questions & Answers
I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Discussion started by: westmoreland
1 Replies
LEARN ABOUT DEBIAN
shell-quote
SHELL-QUOTE(1p) User Contributed Perl Documentation SHELL-QUOTE(1p)
NAME
shell-quote - quote arguments for safe use, unmodified in a shell command
SYNOPSIS
shell-quote [switch]... arg...
DESCRIPTION
shell-quote lets you pass arbitrary strings through the shell so that they won't be changed by the shell. This lets you process commands
or files with embedded white space or shell globbing characters safely. Here are a few examples.
EXAMPLES
ssh preserving args
When running a remote command with ssh, ssh doesn't preserve the separate arguments it receives. It just joins them with spaces and
passes them to "$SHELL -c". This doesn't work as intended:
ssh host touch 'hi there' # fails
It creates 2 files, hi and there. Instead, do this:
cmd=`shell-quote touch 'hi there'`
ssh host "$cmd"
This gives you just 1 file, hi there.
process find output
It's not ordinarily possible to process an arbitrary list of files output by find with a shell script. Anything you put in $IFS to
split up the output could legitimately be in a file's name. Here's how you can do it using shell-quote:
eval set -- `find -type f -print0 | xargs -0 shell-quote --`
debug shell scripts
shell-quote is better than echo for debugging shell scripts.
debug() {
[ -z "$debug" ] || shell-quote "debug:" "$@"
}
With echo you can't tell the difference between "debug 'foo bar'" and "debug foo bar", but with shell-quote you can.
save a command for later
shell-quote can be used to build up a shell command to run later. Say you want the user to be able to give you switches for a command
you're going to run. If you don't want the switches to be re-evaluated by the shell (which is usually a good idea, else there are
things the user can't pass through), you can do something like this:
user_switches=
while [ $# != 0 ]
do
case x$1 in
x--pass-through)
[ $# -gt 1 ] || die "need an argument for $1"
user_switches="$user_switches "`shell-quote -- "$2"`
shift;;
# process other switches
esac
shift
done
# later
eval "shell-quote some-command $user_switches my args"
OPTIONS
--debug
Turn debugging on.
--help
Show the usage message and die.
--version
Show the version number and exit.
AVAILABILITY
The code is licensed under the GNU GPL. Check http://www.argon.org/~roderick/ or CPAN for updated versions.
AUTHOR
Roderick Schertler <roderick@argon.org>
perl v5.8.4 2005-05-03 SHELL-QUOTE(1p)