I am trying to change an IP address on a machine running HPUX10
After I change it I can ping it from the outside but it completely locks the console. After a reboot it returns back to its previous IP. Any ideas??
Thanks
Brian (7 Replies)
why the ifconfig command is not working in my machine?
it says "-bash: ifconfig: command not found"
why its says that?
actually i m looking for "how can I know the Network Interface Card physical address?"
Requesting u all for help.
thanks (3 Replies)
I have been looking in the scripts for interface management, in an effort to kick off a script of my own on any "significant network event" (I will qualify that in a bit)
I managed to add a check to tell netplugd to run my script every time there is a hot-plug event. Now I need to make it so my... (0 Replies)
Hello everyone.
Im using last redhat enterprise edition and in my working environment, i'm always reconfiguring both interfaces , eth0 and eth1, everytime i change any interface, (i use ifconfig to change ip, and after i execute "/etc/init.d/network restart") my "/etc/hosts" file... (9 Replies)
I have a little script in the /etc/network/if-up.d (debian). It should do something and write the output to a log file. But it doesn't seem to work.
ifup wlan0 dosomething >> /var/log/dosomething.log
I would like to add the date to the output, can somebody help me please?
Thanks! (6 Replies)
Unable to run the ifconfig in my home dir..
I did add adding /sbin and /usr/sbin in th PATH
But still unable to get that ..
Am using red hat linux
cat /etc/redhat-release
Red Hat Enterprise Linux Server release 5.3 (Tikanga) (3 Replies)
What would be the command to remove the IP address from an interface?
I want to remove the ip from this interface:
ce3: flags=1000803<UP,BROADCAST,MULTICAST,IPv4> mtu 1500 index 5
inet 155.216.13.74 netmask fffffff0 broadcast 155.216.13.79
ether 0:3:ba:da:a6:96 (3 Replies)
I have a binary that runs ifdown (to bring down wireless interface). When i run it from php, it is not being run. Is it because the Apache server (php) is run as non-root user?
Need Help! :confused: How can i fix this problem? (1 Reply)
I've got an issue with a VMWare server running RHEL 6.3 that has dual E1000 NICs. I have configured the cards as I would normally do in /etc/sysconfig/network-scripts as ifcfg-eth0 and ifcfg-eth1. I can execute ifup eth0 and bring the interface up quite happily, however when I execute ifup eth1 it... (2 Replies)
Discussion started by: phaedrus
2 Replies
LEARN ABOUT SUSE
pppoe-sniff
PPPOE-SNIFF(8) System Manager's Manual PPPOE-SNIFF(8)NAME
pppoe-sniff - examine network for non-standard PPPoE frames
SYNOPSIS
pppoe-sniff [options]
DESCRIPTION
pppoe-sniff listens for likely-looking PPPoE PADR and session frames and deduces extra options required for pppoe(8) to work.
Some DSL providers seem to use non-standard frame types for PPPoE frames, and/or require a certain value in the Service-Name field. It is
often easier to sniff those values from a machine which can successfully connect rather than try to pry them out of the DSL provider.
To use pppoe-sniff, you need two computers, a DSL modem and an Ethernet hub (not an Ethernet switch.)
If the DSL modem normally connects directly to your computer's Ethernet card, connect it to the "uplink" port on the Ethernet hub. Plug
two computers into normal ports on the hub. On one computer, run whatever software the DSL provider gave you on whatever operating system
the DSL provider supports. On the other computer, run Linux and log in as root.
On the Linux machine, put the Ethernet interface into promiscuous mode and start pppoe-sniff. If the ethernet interface is eth0, for exam-
ple, type these commands:
ifconfig eth0 promisc
pppoe-sniff -I eth0
On the other machine, start your DSL connection as usual. After a short time, pppoe-sniff should print recommendations for the value of
PPPOE_EXTRA. Set this value in /etc/ppp/pppoe.conf. If pppoe-sniff indicates that something special is required in PPPOE_EXTRA, please e-
mail this to pppoe@roaringpenguin.com along with the name of your ISP and the manufacturer and model number of your DSL modem. This infor-
mation will be collated and provided on the PPPoE web page for users who do not have two computers.
After pppoe-sniff finishes (or you stop it if it seems hung), remember to turn off promiscuous mode:
ifconfig eth0 -promisc
OPTIONS -I interface
The -I option specifies the Ethernet interface to use. Under Linux, it is typically eth0 or eth1. The interface should be "up" and
in promiscuous mode before you start pppoe-sniff.
-V The -V option causes pppoe-sniff to print its version number and exit.
BUGS
pppoe-sniff only works on Linux.
AUTHORS
pppoe-sniff was written by David F. Skoll <dfs@roaringpenguin.com>.
The pppoe home page is http://www.roaringpenguin.com/pppoe/.
SEE ALSO pppd(8), pppoe(8), pppoe-sniff(8), pppoe-relay(8), /usr/share/doc/pppoe/README.Debian.gz
4th Berkeley Distribution 3 July 2000 PPPOE-SNIFF(8)