11-04-2009
i can't read hard disk scsi
i was installing i my computer windows xp and sco
when i use knoppix5.0 live to read scsi partition wish sco was installing
show me message that i have not permission to acces in scsi hard drive
help me please
10 More Discussions You Might Find Interesting
1. Filesystems, Disks and Memory
I was using an external SCSI disk on a Sun Ultra60 (Solaris 7) as the boot device. It was labelled c1t0d0. I then moved it into the internal removable mounts and it should become c0t0d0, but it apparently didn't change properly. When the machine boots, it gets host information from the disk... (2 Replies)
Discussion started by: Solaris
2 Replies
2. UNIX for Dummies Questions & Answers
Hello agian !
What is the difference between SCSI and IDE hard disks ?
I have Intel PC and when i check i have Generic IDE TYPE DISK0
is IDE hard disk is ok for Solrais ? or should i buy the SCSI hard disk ?
Thanks
Abid Malik (3 Replies)
Discussion started by: abidmalik
3 Replies
3. Filesystems, Disks and Memory
Hi
I have 2 75GB SCSI hard drives and 2 250GB SATA hard drives which are using RAID Level 1 respectively. I wana have both FTP and Apache installed on them as services. I'm wondering what's the best partitioning schem? I wana use FC3 as my OS, so, I thought I can use the 75GB hard drive as the /... (0 Replies)
Discussion started by: sirbijan
0 Replies
4. UNIX for Dummies Questions & Answers
Someone gave me a small external SCSI hard drive for my SunOS 5.8 test system. How do I make Unix see the hard drive? (2 Replies)
Discussion started by: FredSmith
2 Replies
5. Solaris
Guys,
I have googled and checked this forum in detail and couldn't find any satisfactory answers for my problem.
I am trying to connect a external SCSI hard Drive(Sea Gate) to a Ultra 80.
I connected it powered it up and at OK prompt did : boot -r
system comes up and complains about not... (6 Replies)
Discussion started by: ajnabi
6 Replies
6. SCO
hi
I've a fresh installation of SCO 5.0.7 on the IDE hard disk.
For SCSI hard disk I can declare, for example blc disk driver using:
# mkdev hd 0 SCSI-0 0 blc 0but it works for IDE hard disk? (3 Replies)
Discussion started by: ccc
3 Replies
7. Linux
Hi all,
I'm kind of new to programming in Linux & c/c++. I'm currently writing a FileManager using Ubuntu Linux(10.10) for Learning Purposes. I've got started on this project by creating a loopback device to be used as my virtual hard disk. After creating the loop back hard disk and mounting it... (23 Replies)
Discussion started by: shen747
23 Replies
8. SCO
OK group, it's been 12 years since I worked with SCO. I need some direction here:
SCO Openserver 5.07
I have a server with a bad motherboard. I have moved the SCSI adapter and hard drive to another computer. This new server has different hardware so I must install the chipset drivers for... (1 Reply)
Discussion started by: jscholz
1 Replies
9. Solaris
To Solaris 8 Experts,
Please let me know what's the best method / procedure as well as the Solaris 8 commands for accomplishing the following tasks on a production Sun Enterprise 250 Server running Sun Solaris 8 Operating System:
1. Make an exact image/copy of the SCSI Hard Drive in the... (3 Replies)
Discussion started by: ssabet
3 Replies
10. Solaris
Hi,
I have a Sun Fire V440 server that fails to boot up correctly. A lot of services are not started and the sytems acts really slow to commands. During boot I can see the following Error:
WARNING: /pci@1f,700000/scsi@2/sd@0,0 (sd1):
SCSI transport failed: reason 'reset': retrying... (15 Replies)
Discussion started by: oliwei
15 Replies
SD(4) Linux Programmer's Manual SD(4)
NAME
sd - Driver for SCSI Disk Drives
SYNOPSIS
#include <linux/hdreg.h> /* for HDIO_GETGEO */ #include <linux/fs.h> /* for BLKGETSIZE and BLKRRPART */
CONFIG
The block device name has the following form: sdlp, where l is a letter denoting the physical drive, and p is a number denoting the parti-
tion on that physical drive. Often, the partition number, p, will be left off when the device corresponds to the whole drive.
SCSI disks have a major device number of 8, and a minor device number of the form (16 * drive_number) + partition_number, where drive_num-
ber is the number of the physical drive in order of detection, and partition_number is as follows:
partition 0 is the whole drive
partitions 1-4 are the DOS "primary" partitions
partitions 5-8 are the DOS "extended" (or "logical") partitions
For example, /dev/sda will have major 8, minor 0, and will refer to all of the first SCSI drive in the system; and /dev/sdb3 will have
major 8, minor 19, and will refer to the third DOS "primary" partition on the second SCSI drive in the system.
At this time, only block devices are provided. Raw devices have not yet been implemented.
DESCRIPTION
The following ioctls are provided:
HDIO_GETGEO
Returns the BIOS disk parameters in the following structure:
struct hd_geometry {
unsigned char heads;
unsigned char sectors;
unsigned short cylinders;
unsigned long start;
};
A pointer to this structure is passed as the ioctl(2) parameter.
The information returned in the parameter is the disk geometry of the drive as understood by DOS! This geometry is not the physical
geometry of the drive. It is used when constructing the drive's partition table, however, and is needed for convenient operation of
fdisk(1), efdisk(1), and lilo(1). If the geometry information is not available, zero will be returned for all of the parameters.
BLKGETSIZE
Returns the device size in sectors. The ioctl(2) parameter should be a pointer to a long.
BLKRRPART
Forces a re-read of the SCSI disk partition tables. No parameter is needed.
The scsi(4) ioctls are also supported. If the ioctl(2) parameter is required, and it is NULL, then ioctl() will return -EINVAL.
FILES
/dev/sd[a-h]: the whole device
/dev/sd[a-h][0-8]: individual block partitions
SEE ALSO
scsi(4)
1992-12-17 SD(4)