11-03-2009
AIX OS problem? network problem?
Dear ALL.
I installed AIX OS on customer sites.
but Only one site is too slow when I connected telnet, ftp..
Ping is too fast. but telnet and FTP is not connected..
of course i check the configuration file on aix but it's normal.
Do any Idea??
thanks in advance.
- Jun -
10 More Discussions You Might Find Interesting
1. AIX
I am posting this as an FYI. I burned a lot of time on digging for this solution. The problem was performance between newer AIX p series boxes and a sun 4500 with a fiber nic. I tried many misc. solutions but this turned out to fix the issue. My bandwidth benchmark went from around 20MB/sec to... (1 Reply)
Discussion started by: chuckw
1 Replies
2. UNIX for Advanced & Expert Users
Hi expert,
Need some help on network interface issue..
I have added 2 x NIC card onto the Ultra 2 system recently and configured as hme1 and hme2. I have unconfigured the onboard hme0 network interface and it was running fine till few days later, i keep recieving error messages showing hme0... (6 Replies)
Discussion started by: sc2005
6 Replies
3. Solaris
Hi All,
This is regarding problem with two servers...
EX:- server1(HP) is not able to connect with proxy server server2(SUN BOX)
But we can able to login.... server1 is not able to pickup any data from the proxy server...
checked in the sunbox...
# ping bdhp5050
server1 is alive
... (1 Reply)
Discussion started by: jeelans
1 Replies
4. UNIX for Dummies Questions & Answers
I am using network printer through ip address. when you check with lpstat it says, "Waiting for <printer name> to come up. other network printers working. this also work before. but now not working. scheduler & accept print jobs working. wht could be the problem (1 Reply)
Discussion started by: ajantha
1 Replies
5. IP Networking
Folks;
I have 2 SUSE servers (192.168.157.100 & 192.168.157.101) both are similar and has the same gateway 192.168.157.1
I can connect to the second one from my PC just fine (192.168.157.101).
The problem is i couldn't connect to the first one using SSH even after i disabled the firewall. when i... (3 Replies)
Discussion started by: Katkota
3 Replies
6. IP Networking
system config. Red hat ES 5 . multiple network cards. front end and back end networks.
Problem:
Here is what I have diagnosed on linux 6 .....other machines on the network if you try to get there do not see linux 6, a ping results in “no route to host” message. However the system is running... (4 Replies)
Discussion started by: frankkahle
4 Replies
7. AIX
I ‘m beginner on unix
I want to move an unix aix post 5.2 on distant site for use catia V4 with a foundation of data accommodated by a serveur windows 2003 and an environment accommodated on the serveur aix.
The computer was linked up by IP (122.0.0.8) with waiter 2003 (via NFS) and the waiter... (8 Replies)
Discussion started by: astiaous
8 Replies
8. AIX
Hi everbody;
I have 2 p520 machines and created a vio server for each one (vio01 - vio02). I created 3 AIX 5.3 lpars on vio02 and 3 AIX 6.1 lpars on vio01. The problem is when 2 lpars are activated, i can ping gateway from both lpars and vio; but when i activate 3rd lpar, network downs and none of... (2 Replies)
Discussion started by: lordofdarkness
2 Replies
9. Homework & Coursework Questions
Assuming there are 6 machines A,B,C,D,E, and F.
I need to create user Lanson on machine A, Joanna on machine B, Jhonson on machine C, Levette on machine D, Jhon on machine E, and Emerson on machine F.
a) Lanson, and Joanna must be in the same group.
b) Levette must have all his the files... (5 Replies)
Discussion started by: Auser
5 Replies
10. Android
Good day, everybody! I have a mobile phone (LG Optimus L5) with Android 4.0.3 and a tablet (PocketBook SurfPad 2) with Android 4.1.1 and I have problem with wireless network on these devices. Laptops don't have such problem. My wireless network organisation is a modem connected with an access point... (11 Replies)
Discussion started by: qzxcvbnm
11 Replies
nstrtel(5) File Formats Manual nstrtel(5)
NAME
nstrtel - specifies the number of telnet device files the kernel can support for incoming telnet sessions
VALUES
Failsafe
Default
Allowed values
(Subject to available physical memory.)
It is best to use the default value, and there should not be any need to lower it. However, if the simultaneous telnet connection load is
very high, then the value of could be increased.
Recommended values
(Default value.)
DESCRIPTION
The telnet daemon uses two STREAMS-based pseudo-terminal drivers and The kernel parameter, can be used to tune the number of pseudo-termi-
nals. specifies the number of kernel data structures that are created at system boot time that are required to support the device files
used by incoming telnet sessions on a server. If the command or SAM is used to create more telnet device files, the value of must be
increased accordingly or the device files cannot be used because there are no kernel data structures available for communicating with the
system.
Who Is Expected to Change This Tunable?
Anyone.
Restrictions on Changing
Changes to this tunable take effect at the next reboot.
When Should the Value of This Tunable Be Raised?
When there is an increase in the load of telnet connections and there are no device files available to open telnet connections, then this
kernel parameter should be increased.
When the error is encountered, then the device files have been exhausted and should be raised. Once the value of is raised, should be run
to create new device files. (If SAM is used to raise the value of is run automatically.)
What Are the Side Effects of Raising the Value of This Tunable?
More resources would be consumed. Extra kernel data structures, and extra device files may clog the system.
When Should the Value of This Tunable Be Lowered?
It is not advisable to lower the tunable value from the default value. Consult HP Support before lowering this tunable from the default
value.
What Are the Side Effects of Lowering the Value of This Tunable?
Though not recommended, there would not be any side effects.
What Other Tunables Should Be Changed at the Same Time?
None.
WARNINGS
All HP-UX kernel tunable parameters are release specific. This parameter may be removed or have its meaning changed in future releases of
HP-UX.
Installation of optional kernel software, from HP or other vendors, may cause changes to tunable parameter values. After installation,
some tunable parameters may no longer be at the default or recommended values. For information about the effects of installation on tun-
able values, consult the documentation for the kernel software being installed. For information about optional kernel software that was
factory installed on your system, see at
AUTHOR
was developed by HP.
SEE ALSO
insf(1M), telnetd(1M), telm(7), tels(7).
Tunable Kernel Parameters nstrtel(5)