10-29-2009
Not all programs use the partition type at all.
Also, you can make swap out of a file. How could that work if you were reliant on a partition type?
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
When i re-updated my system i set my swap at 500 MB. I have 256 in ram and have never even gone into the 250 mb of swap that i had originally configured. How do I reduce the swap? (3 Replies)
Discussion started by: macdonto
3 Replies
2. UNIX for Dummies Questions & Answers
Is it really so that if swap will be located in the begining of hard drive, than it will work faster? (1 Reply)
Discussion started by: Ty3
1 Replies
3. AIX
I have an unsupported legacy server:
# uname -a
AIX ibmms01 3 4 0054960A4C00
Following a period of poor performance, it was investigated using vmstat 10.
There upto 10 blocked kernel threads reported, and free memory was down to 123. The scan rate was high, 3000+ with lots of page in page... (6 Replies)
Discussion started by: jabberwocky
6 Replies
4. Solaris
When i try to type swap -l ,nothing come out but blinking.
May i know what is the problem and solutions ?
thanks (6 Replies)
Discussion started by: Farbegas
6 Replies
5. Solaris
Hello and thanks in advance.
I have a Sun box with raid 1 on the O/S disks using solaris svm.
I want to unmirror my swap partition, and add the slice on the second disk as an additional swap device. This would give me twice as much swap space.
I have been warned not to do this by some... (3 Replies)
Discussion started by: BG_JrAdmin
3 Replies
6. HP-UX
I have a HP-UX B.11.23 server with 16 gb of memory 84 gb of swap configured. I am being pushed to define more swap to try and get more Tuxedo domains to start. At what point do we have too much swap for the amount of memory? Thanks in advance. (11 Replies)
Discussion started by: scotbuff
11 Replies
7. HP-UX
Hi
I have an integrity machine rx7620 and rx8640 running hp-ux 11.31. I'm planning to fine tune the system:
- I would like to know when does the memory swap space spill over to the device swap space?
- And how much % of memory swap utilization should be specified (swap space device... (6 Replies)
Discussion started by: lamoul
6 Replies
8. Red Hat
Hi,
I have added a new disk to production server. How to make it visible to os and how to configure it. I also want to add some space from that disk to swap space. Please help me out. (1 Reply)
Discussion started by: chetansingh23
1 Replies
9. Solaris
Hi,
Can somebody please help here, since iam just a beginner.
According to my book knowledge.
the Avalilable memory calculated by swap -l (includes only swap) should be small as compared to swap -s value(includes Virtual memory=swap +physical).
but this is quite opposite in my case.
swap... (6 Replies)
Discussion started by: Laxxi
6 Replies
10. Solaris
Hi Solaris Folks :),
I need to calculate the swap usage on solaris server, please let me understand the output of below swap -s and swap -l commands.
$swap -s
total: 1774912k bytes allocated + 240616k reserved = 2015528k used, 14542512k available
$swap -l
swapfile dev swaplo... (6 Replies)
Discussion started by: seenuvasan1985
6 Replies
LEARN ABOUT ULTRIX
disktab
disktab(5) File Formats Manual disktab(5)
Name
disktab - disk description file
Syntax
#include <disktab.h>
Description
The file is a simple data base that describes disk geometries and disk partition characteristics. The format is patterned after the termi-
nal data base. Entries in consist of a number of fields separated by colons (:). The first entry for each disk gives the names that are
known for the disk, separated by vertical bars (|). The last name given should be a long name fully identifying the disk.
The following list indicates the normal values stored for each disk entry:
Name Type Description
ns num Number of sectors per track
nt num Number of tracks per cylinder
nc num Total number of cylinders on the disk
ba num Block size for partition `a' (bytes)
bd num Block size for partition `d' (bytes)
be num Block size for partition `e' (bytes)
bf num Block size for partition `f' (bytes)
bg num Block size for partition `g' (bytes)
bh num Block size for partition `h' (bytes)
fa num Fragment size for partition `a' (bytes)
fd num Fragment size for partition `d' (bytes)
fe num Fragment size for partition `e' (bytes)
ff num Fragment size for partition `f' (bytes)
fg num Fragment size for partition `g' (bytes)
fh num Fragment size for partition `h' (bytes)
pa num Size of partition `a' in sectors
pb num Size of partition `b' in sectors
pc num Size of partition `c' in sectors
pd num Size of partition `d' in sectors
pe num Size of partition `e' in sectors
pf num Size of partition `f' in sectors
pg num Size of partition `g' in sectors
ph num Size of partition `h' in sectors
se num Sector size in bytes
ty str Type of disk (e.g. removable, winchester)
The entries can be automatically generated with the program.
Files
See Also
chpt(8), newfs(8)
disktab(5)