Login or Register to Ask a Question and Join Our Community

Sponsored Content
Full Discussion: Break command on rsc of sunfire v890 server
Operating Systems Solaris Break command on rsc of sunfire v890 server Post 302365606 by girish.batra on Tuesday 27th of October 2009 02:26:27 PM
Old 10-27-2009
Thanks for the reply DukeNuke. Sorry for Delay as I was not well.

We even run so many times diagnotic at max level also but we didn't get any error in that. We even change the I/O & Mother Board also. but even then we did get the system into hang state. That time Our patch level was 120011-14 also . Then we update patch level of OS to 141414-10 also, after that system goes into hange state only once also. But before patch activity system goes into hang state around 15 to 17 times.

As this is a databse server into cluster mode we cannot do the sun cluster patch activity before that server do not comes to stable state. Same OS patch level & cluster level activity on other server till the hang server do not comes to stable state.

Kindly help on this matter also
 

10 More Discussions You Might Find Interesting

1. Solaris

[help]network error after reboot server v890 sparc

hi expert, i had reinstall the sun v890 server solaris 8 and also do mirroring, i had configure the network for the server (hostname.eri0,hosts,netmasks,nodename,etc) after i reboot get and error messages below : Setting default IPv4 interface for multicast: add net 224.0/4: gateway... (5 Replies)
Discussion started by: bucci
5 Replies

2. Solaris

RSC on SunFire 480R

When I try to connect to a RSC console using the serial port by modem, I can connect but I can't type username neither password because the screen scrolls up. At the loghistory shows the message: RSC Login failure. Using serial without modem, it works well. (2 Replies)
Discussion started by: Livio
2 Replies

3. Solaris

Sun V890: RSC firmware not responding

Hi all, After the V890 server shutdown unexpectedly, it became unaccessible from RSC. There is one error message about it: rscadm: RSC firmware not responding Do you have experienced this? Please help! (1 Reply)
Discussion started by: bamboonix
1 Replies

4. UNIX for Dummies Questions & Answers

Can anyone break down this find command for me?

find . "(" -name a.out -o -name core ")" -exec rm {} \; Specifically What files are trying to be found What does the -o do in this command What is the result if the files are found What does the command do if the files are not found What does the . after the word find mean thanks in... (1 Reply)
Discussion started by: knp808
1 Replies

5. Shell Programming and Scripting

Break command

have a query on this break. I am using a program where I am using a while loop to execute it. It will get into a file take the first file and then ping it and if the ip is reachable then it will mail. Now what happens is that when i ping the ip it does nopt come out of the loop and it says "reply... (11 Replies)
Discussion started by: venkidhadha
11 Replies

6. Solaris

Sun Fire V890 - Unable to access RSC or Serial console

Hello Folks, I am having trouble to login to rsc or serial console of V890. The rsc2.2.3 has been configured with required parameters, resetrs and even rebooted. When serial port is connected to laptop, The hyper terminal does not get the console or POSt messages when the server is rebooting... (8 Replies)
Discussion started by: defflepord
8 Replies

7. Solaris

SunFire V890 error -256 when boot

Hi all! I've a machine - SunFire V890, it've been failed by OS error for 2 weeks ago, and now, I must reinstall OS (Solaris 10 2009), the progress was successful, but when I reboot, it displayed the error like : Error -256: Last trap memory ... access aligned Error -256: Last trap memory... (1 Reply)
Discussion started by: trantuananh24hg
1 Replies

8. Solaris

How to boot from Cd-rom in Server Sunfire v250?

Howto boot from Cd-rom in Server Sunfire v250? The system can't boot because the filesystem is corrupt. The system say: run manually fsck -F ufs /dev/rdsk/c0t0d0s5 But, I don't now how to make this. I tried use stop + a, but nothing hapend. Someone can I help? (13 Replies)
Discussion started by: vigux
13 Replies

9. Solaris

Sunfire X4100 server

Hi, I am currently on Sunfire X4100. This server doesn't have CDROM drive. Also I can't get to the OK prompt. From my laptop, I am connected to the management port using the Cisco Blue cable. Please advise how can I get to the OK prompt. Also the server is so loud. Will the FAN cool... (1 Reply)
Discussion started by: samnyc
1 Replies

10. Solaris

Can't use 'break' command, Can't access 'ok' prompt.

Hi I have A Sun Ultra Enterprise 450 server, it has Solaris installed on it. I have A serial terminal hooked up to it (nullmodem cable plugged into serial port 1 on the box, and the other end plugged into the serial port of A laptop (NEC Versa M300)) The laptop is running Ubuntu 12.04.2... (3 Replies)
Discussion started by: SomeoneTwo
3 Replies

LEARN ABOUT LINUX

edit-patch

EDIT-PATCH(1)                                                 General Commands Manual                                                EDIT-PATCH(1)

NAME

       edit-patch, add-patch - tool for preparing patches for Debian source packages

SYNOPSIS

       edit-patch path/to/patch

       add-patch path/to/patch

DESCRIPTION

       edit-patch is a wrapper script around the Quilt, CDBS, and dpatch patch systems. It simplifies the process of preparing and editing patches
       to Debian source packages and allows the user to not have to be concerned with which patch system is in use.   Run  from  inside  the  root
       directory of the source package, edit-patch can be used to edit existing patches located in debian/patches.

       It can also be used to incorporate new patches.  If pointed at a patch not already present, it will copy the patch to debian/patches in the
       correct format for the patch system in use.  Next, the patch is applied and a subshell is opened in order to edit the patch.   Typing  exit
       or pressing Ctrl-d will close the subshell and launch an editor to record the debian/changelog entry.

       edit-patch  is  integrated  with  the  Bazaar  and Git version control systems.  The patch will be automatically added to the tree, and the
       debian/changelog entry will be used as the commit message.

       If no patch system is present, the patch is applied inline, and a copy is stored in debian/patches-applied.

       add-patch is the non-interactive version of edit-patch.  The patch will be incorporated but no editor or subshell will be spawned.

AUTHORS

       edit-patch was written by Daniel Holbach <daniel.holbach@canonical.com>,  Michael  Vogt  <michael.vogt@canonical.com>,  and  David  Futcher
       <bobbo@ubuntu.com>.

       This manual page was written by Andrew Starr-Bochicchio <a.starr.b@gmail.com>.

       Both are released under the terms of the GNU General Public License, version 3.

DEBIAN                                                           Debian Utilities                                                    EDIT-PATCH(1)
All times are GMT -4. The time now is 02:52 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy