10-27-2009
Thoughts:
1. Any DHCP interfering with your config?
2. Remember to enable the "START Now" option in smit when configuring interfaces.
9 More Discussions You Might Find Interesting
1. Filesystems, Disks and Memory
Hi
I have 2 75GB SCSI hard drives and 2 250GB SATA hard drives which are using RAID Level 1 respectively. I wana have both FTP and Apache installed on them as services. I'm wondering what's the best partitioning schem? I wana use FC3 as my OS, so, I thought I can use the 75GB hard drive as the /... (0 Replies)
Discussion started by: sirbijan
0 Replies
2. Solaris
Hi.
I have a Solaris 10 server that's taking about 20secs to respond to telnet or ftp commands. Has anyone ever seen something like that? Can you tell me where to start troubleshooting please? I logged in and did a prtstat, but nothing is jumping out as an issue. (8 Replies)
Discussion started by: bbbngowc
8 Replies
3. AIX
Hi guys,
Is there a command in AIX similar to ps, but shows memory usage by application? I'm trying to track down a rogue application that's using up all 32GB of the available systems memory and causing the the system to page to disk. (4 Replies)
Discussion started by: bbbngowc
4 Replies
4. Solaris
Dear all,
I am a newbie in solaris and I need your advice.
I have a Solaris version 5.9 installed on Sunfire V240.
I am able to ssh the machine from putty remotely.
My problem is that I cannot see the display from KVM switch I have connected to it. I need also to be able to see the GUI... (2 Replies)
Discussion started by: mbouster
2 Replies
5. SCO
Hi all
I have installed a demo version of SCO OpenServer 5.0.2, I finally found it is Desktop Interface, I would like to know how to change its interface to dos based interface?
If you have any ideas, please tell me then. Thank you (2 Replies)
Discussion started by: TinhNhi
2 Replies
6. IP Networking
This is my situation
DOS pc serial cable (sl0) Linux Pc eth1
192.168.0.10 <-------------------->192.168.0.2 <------------>192.168.0.1 (router)
I connected the linux pc and the dos pc with a SLIP (serial line internet protocol), so they can communicate in the sl0 interface.
... (3 Replies)
Discussion started by: mghis
3 Replies
7. Linux
Hi all,
I'm kind of new to programming in Linux & c/c++. I'm currently writing a FileManager using Ubuntu Linux(10.10) for Learning Purposes. I've got started on this project by creating a loopback device to be used as my virtual hard disk. After creating the loop back hard disk and mounting it... (23 Replies)
Discussion started by: shen747
23 Replies
8. UNIX for Dummies Questions & Answers
I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Discussion started by: westmoreland
1 Replies
9. Hardware
Hi,
I have broken my laptop hard drive so I would like to put it in an external box to backup my documents.
I have a doubt whether the interface of the hard disk is sata or ide.
Inside notes attached, is reported "controller SATA AHCI" but on the model section is given IDE hard disk
... (1 Reply)
Discussion started by: nash83
1 Replies
EPAIR(4) BSD Kernel Interfaces Manual EPAIR(4)
NAME
epair -- A pair of virtual back-to-back connected Ethernet interfaces.
SYNOPSIS
To compile this driver into the kernel, place the following line in your kernel configuration file:
device epair
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
if_epair_load="YES"
DESCRIPTION
The epair is a pair of Ethernet-like software interfaces, which are connected back-to-back with a virtual cross-over cable.
Each epair interface pair is created at runtime using interface cloning. This is most easily done with the ifconfig(8) create command or
using the cloned_interfaces variable in rc.conf(5). While for cloning you only give either epair or epair<n> the epair pair will be named
like epair<n>[ab]. This means the names of the first epair interfaces will be epair0a and epair0b.
Like any other Ethernet interface, an epair needs to have a network address. Each epair will be assigned a locally administered address by
default, that is only guaranteed to be unique within one network stack. To change the default addresses one may use the SIOCSIFADDR ioctl(2)
or ifconfig(8) utility.
The basic intend is to provide connectivity between two virtual network stack instances. When connected to a if_bridge(4) one end of the
interface pair can also be part of another (virtual) LAN. As with any other Ethernet interface one can configure vlan(4) support on top of
it.
SEE ALSO
ioctl(2), altq(4), bpf(4), if_bridge(4), vlan(4), loader.conf(5,) rc.conf(5), ifconfig(8)
HISTORY
The epair interface first appeared in FreeBSD 8.0.
AUTHORS
The epair interface was written by Bjoern A. Zeeb, CK Software GmbH, under sponsorship from the FreeBSD Foundation.
BSD
July 26, 2009 BSD