10-19-2009
NAT detection
hellou, can anybody help me with nat detection in real time ? i prefer some detection script because i try some nat detection program's for example p0f or i'm using tcpdump, but i would get contain of specific packet. Some ideas?
9 More Discussions You Might Find Interesting
1. IP Networking
Hi All!
I have a Pentium 100 (32 MBRAM) with FreeBSD 4.4 installed on it and I am using it as a gateway. When I am downloading (or uploading) stuff simultaneously I see that natd is using up to 100% of the cpu capacity, hence the internet connection becomes blocked.
My guess is I will have... (1 Reply)
Discussion started by: Ivo
1 Replies
2. BSD
how do i configure proxy in freeBSD or NAT so that when i set it up as a server can connect other to my new gateway (0 Replies)
Discussion started by: AkinOkin
0 Replies
3. IP Networking
i have a firewall with two interfaces eth0 and eth1, eth0 is connected to an external network, and eth0 is connected to a private lan.
im using this command for NAT
iptables -A POSTROUTING -t nat -s 192.168.0.0/24 -o eth0 -j SNAT --to-source 223.0.0.3
my questions are :
1) how can i... (4 Replies)
Discussion started by: ratamahatta
4 Replies
4. IP Networking
Hi
Could anybody tell me the solaris command to display the NAT address
Thanks in advance (5 Replies)
Discussion started by: axes
5 Replies
5. IP Networking
Hi All,
Is there any possibility to change the IP address of a package according to its MAC address. It would be a sort of L2 NAT. (i.e. If the MAC address is 00:1A:A0:1E:XX:XX so the dir IP will be 192.168.X.X)
Thanks!. (4 Replies)
Discussion started by: lagigliaivan
4 Replies
6. Solaris
Hi everybody,
I'm running on Solaris 10 X86 (update 1009).
I would like to make NAT's rule. I explain you.
On Solaris, I configure the principal interface e1000g0 with IP : 192.168.0.33
I created the first logical interface like that :
ifconfig e1000g0 addif 192.168.0.40 netmask... (0 Replies)
Discussion started by: aureliensm
0 Replies
7. Programming
Hey, for the purpose of a research project I need to know if a specific type of parallel processing is being utilized by any user-run programs. Is there a way to detect whether a program either returns a value to another program at the end of execution, or just utilizes any form of parallel... (4 Replies)
Discussion started by: azar.zorn
4 Replies
8. Infrastructure Monitoring
Hello,
I am facing this scenario: three or more remote LAN (peripheral offices), with the same devices (printers, NAS) in each of them. Those LANs have the same network addresses, i.e.192.168.1.* (are connected to WAN via NAT).
I need to collect snmp traps from a central server (public IP).... (4 Replies)
Discussion started by: neutrino
4 Replies
9. Solaris
Hi.
I am attempting to set up an OpenVPN server on my Solaris 11 box by following all the Linux guides. Thus far I have a working VPN that I can connect to and ssh onto my VPN server over which is great but not what I require long term.
I would like to route all VPN client requests for addresses... (0 Replies)
Discussion started by: nickb1976
0 Replies
LEARN ABOUT DEBIAN
gnunet-nat-server
GNUNET-NAT-SERVER(1) General Commands Manual GNUNET-NAT-SERVER(1)
NAME
gnunet-nat-server - help GNUnet setup test network setup with NAT
SYNOPSIS
gnunet-nat-server [options] PORT
DESCRIPTION
Normal GNUnet end-users should not concern themselves with gnunet-nat-server. In fact, distributions are encouraged to consider not ship-
ping it at all. Running gnunet-nat-server's is similar to running hostlist servers: it is a special service to the community with special
requirements and no benefit to those running the service.
This program will listen on the specified PORT for incoming requests to test a peer's network connectivity. Incoming requests can ask it
to connect to a given IPv4 address (and port) using TCP or UDP and to send a 2-byte test message using the specified address. The program
can also be asked to send a "fake" ICMP response message to a given IPv4 address (for autonomous NAT traversal --- see the description in
the respective research paper).
The idea is that gnunet-nat-server will be run on some trusted hosts with unrestricted connectivity to allow GNUnet users to test their
network configuration. As written, the code allows any user on the Internet to cause the gnunet-nat-server to send 2-bytes of arbitrary
data to any TCP or UDP port at any address. We believe that this is generally harmless.
When running gnunet-nat-server, make sure to use a configuration that disables most NAT options but enables 'enable_nat_client' and sets
'internal_address' to the global IP address of your local host. Also, the gnunet-helper-nat-client should be installed locally and run
with root privileges (SUID), otherwise the gnunet-nat-server will not work properly.
Note that gnunet-nat-server could be run via gnunet-arm but typically is not. Also, the name of the host and port that gnunet-nat-server
is run on should be specified in the NATSERVER option in the [setup] section of the configuration file of hosts that are supposed to auto-
configure with this server.
OPTIONS
-c FILENAME, --config=FILENAME
Use the configuration file FILENAME.
BUGS
Report bugs by using Mantis <https://gnunet.org/bugs/> or by sending electronic mail to <gnunet-developers@gnu.org>
SEE ALSO
gnunet-transport(1)
GNUnet 25 Feb 2012 GNUNET-NAT-SERVER(1)