Sponsored Content
Operating Systems Linux Red Hat [RHEL4.5] server shutdown when I unplug the ethernet cable Post 302362591 by mark54g on Friday 16th of October 2009 02:14:20 PM
Old 10-16-2009
Do you have some sort of cluster service on this machine that tries to fence/disable the node?
 

10 More Discussions You Might Find Interesting

1. Solaris

null modem serial cable for server testing

HI all, i still have a problem when using null modem to see the output from my server(sun ultra en 3000). i followed the instruction from the internet, but it is not working. 1. i am using db9(5 4, 2 rows,put in laptop serial port) and db25(13 12, 2 rows,put in (A) server serial port). 2.... (3 Replies)
Discussion started by: waterbear
3 Replies

2. AIX

server is getting shutdown

Hi Guys, Please help in this...when we start HACMP services ..server is getting shutdon. Error mesg from cluster.log. Apr 14 08:43:27 bascop17 snmpd: NOTICE: SMUX trap: (0 0) (127.0.0.1+46302+1) Apr 14 08:43:33 bascop17 topsvcs: (Recorded using libct_ffdc.a cv 2):::Error ID:... (1 Reply)
Discussion started by: b_manu78
1 Replies

3. IP Networking

How to handle unplugging ethernet cable in socket programming

Hi, I am trying to implement a server-client socket communication. My server and clients are in different PCs. During communications if the ethernet cable is removed from the server side it shows broken pipe due to unable to write on the socket. I want to know how to check whether the ethernet... (0 Replies)
Discussion started by: JagadishB
0 Replies

4. IP Networking

Two Servers via ethernet crossover cable

Hi, I'm trying to communicate two servers (HP DLProliant 380 G5) via a crossover cable, but I don't get them to ping each other. I am working in RHEL 4. These are the steps I've performed: 1) Plugged the crossover cables in eth2. (note: The cable is brand new. Also I built one myself... (3 Replies)
Discussion started by: jrodriguez365
3 Replies

5. UNIX for Dummies Questions & Answers

How to change ethernet cable of iscsi initiator (iscsi client)?

how to change ethernet cable of iscsi initiator (iscsi client) (0 Replies)
Discussion started by: pankajd
0 Replies

6. Programming

How detect TCP/IP socket shutdown when ethernet cable is disconnected

Hi, I want to code TCP/IP client/server in linux application capable to fastly detect ethernet cable disconnection in any condition. So I have activate SO_KEEPALIVE options and set TCP_KEEPCNT, TCP_KEEPIDLE and TCP_KEEPINTVL to 1. When I disconnect ethernet cable I have the following... (5 Replies)
Discussion started by: jeje_clb
5 Replies

7. UNIX for Advanced & Expert Users

Shutdown the Linux server if no one is using the server

Hi All, I want to shutdown the server if no one is actualy using it. Its a linux server. I thought of sending a msg on users terminal for those who all are logged in and expecting a input from them. If they will reply system should not get shutdown else it should not. Can any one... (2 Replies)
Discussion started by: Sadhana
2 Replies

8. AIX

Server Shutdown

Hi, is it possible to find out ip address of user who has shutdown or rebooted the server , I have used the command errpt -a , in that it is showing server rebooted but it is not showing ip address who has shutdown the serve, even I have used command last reboot. Please suggest. Regards, ... (3 Replies)
Discussion started by: manoj.solaris
3 Replies

9. AIX

vio server ethernet to vio client ethernet(concepts confusing)

Hi In the vio server when I do # lsattr -El hdisk*, I get a PVID. The same PVID is also seen when I put the lspv command on the vio client partition. This way Im able to confirm the lun using the PVID. Similarly how does the vio client partition gets the virtual ethernet scsi client adapter... (1 Reply)
Discussion started by: newtoaixos
1 Replies

10. Solaris

Unplug power from Sparc Server T5440 when in OpenBoot

show /HOST command shows that status = OpenBoot Running when in this state, can the power be unplugged from the server ? we are unable to bring the status to "powered off". Even if we issue "stop /SYS" it will momentarily be in the powered off status and then go back to power on... (1 Reply)
Discussion started by: paulk93
1 Replies
asadmin-shutdown(1AS)                                              User Commands                                             asadmin-shutdown(1AS)

NAME
asadmin-shutdown, shutdown - brings down the administration server SYNOPSIS
shutdown [--user admin_user][--password admin_password][--host localhost] [--port 4848][--passwordfile filename][--secure|-s] shutdown gracefully brings down the administration server and all the running instances. You must manually start the administration server to bring it up again. OPTIONS
--user administrative user associated for the instance. --password administrative password corresponding to the administrative user. --host host name of the machine hosting the administrative instance. --port administrative port number associated with the administrative host. --passwordfile file containing passwords appropriate for the command (e.g., administrative instance). --secure if true, uses SSL/TLS to communicate with the administrative instance. Example 1: Using the shutdown command asadmin> shutdown --user admin --password adminadmin --host bluestar --port 4848 Waiting for admin server to shutdown... Admin server has been shutdown EXIT STATUS
0 command executed successfully 1 error in executing the command INTERFACE EQUIVALENT
Administration Server page asadmin-start-instance(1AS), asadmin-stop-instance(1AS), asadmin-restart-instance(1AS)asadmin-start-domain(1AS), asadmin-stop-domain(1AS), asadmin-start-appserv(1AS), asadmin-stop-appserv(1AS) J2EE 1.4 SDK March 2004 asadmin-shutdown(1AS)
All times are GMT -4. The time now is 02:20 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy