Configure Guest LDOM (ldom-guest.ksh) Post: 302361679

6 More Discussions You Might Find Interesting

1. Solaris

Help needed - trying to run commands in Guest LDoms from Control LDOM

Hi Folks, I am used to writing scripts to get info by running commands at local zones level from their respective global zone by using zlogin <localzone> "command>" while remaining at the global zone level. Can the same be done with Guest LDoms while remaining at the control LDOM level? ...

2. Solaris

Network Config on Zone in a Guest LDOM

Solaris for Sparc 11.1 with the latest patches. Created a Guest LDOM with two vnet's net0 and net1, installed a guest whole root, ip exclusive zone that I want to be able to utilize DHCP. I have been able to create the zone but unable to get it to boot because I am unable to assign an anet to it....

3. UNIX for Dummies Questions & Answers

Configure network connectivity as guest O.S under vmware

Hi! I am not sure if this is the right place to post this question. What I did was to download vmware onto my laptop, them install a linux distro as a guest O.S., on VM network configuration I have used "bridge", them I used Virtual Network Editor to chose the network interface, but as I write...

4. Solaris

Disk expansion on LDOM Guest

Hi, There is LDOM Guest where I need to expand /u02 file systems on it. It is residing on a Solaris 11 Hypervisor (Primary Domain). The storage is expanded on vdisk presented to Hypervisor. I need steps to expand the /u02 on LDOM Guest.

5. Solaris

Ldom guest volumen problem t8 Solaris 11

hello to everyone. im new member here. i have a problem with a guest ldom on solaris 11 sparc in a T8. I need to access to disk vds assigned to guest domain but from control domain. I want to modify a parameter in inittab of the guest domain because start guest domain give me problems...

6. UNIX for Beginners Questions & Answers

Solaris 11 LDOM guest network not working

I'm really stuck here. I've created an LDOM on a SPARC T4-1 with Solaris 11.4 to run a copy of Linux for SPARC. I got the Linux ISO installed and Linux itself installed and booted OK. The only thing is is that there's no networking available in the Linux guest. This question is basically the...

LEARN ABOUT DEBIAN

pbuilder-uml.conf

pbuilder-uml.conf(5)						     pbuilder						      pbuilder-uml.conf(5)

NAME

       pbuilder-uml.conf - configuration file for user-mode-linux port of pbuilder

DESCRIPTION

       /etc/pbuilder/pbuilder-uml.conf contains default values used in pbuilder-user-mode-linux program invocation.

FORMAT

       MY_ETH0=tuntap,,,192.168.0.2
	      Configures ethernet setting used for booting linux.  See how rootstrap boots your system, and copy that.

	      Specify --eth0=slirp,12345,/usr/bin/slirp-fullbolt to use the slirp connection.

       UML_IP=192.168.0.3
	      IP address to use for guest OS.

	      This can be set to dhcp for obtaining IP address through DHCP.

       UML_NETMASK=255.255.255.0
	      Guest OS netmask

       UML_NETWORK=192.168.0.0
	      Guest OS network

       UML_BROADCAST=255.255.255.255
	      Guest OS broadcast

       UML_GATEWAY=192.168.0.1
	      Guest OS gateway

       PBUILDER_UML_IMAGE=${HOME}/uml-image
	      Guest OS file system image.

       UML_MOUNT_TMPFS=no
	      Whether to mount tmpfs inside the guest image.  This is probably mostly useless.

       BUILDPLACE=${HOME}/tmp/
	      The  location  which build will take place.  pbuilder-user-mode-linux will place temporary COW files to there.  The user running UML
	      needs to be able to access that directory.

       UML_MEM=128
	      The amount of memory allowed for UML.  Give more value to here.

       UML_HOSTNAME=uml-host
	      The hostname for the UML.

	      The hostname should be available in /etc/hosts so that hostname -f will be able to return the FQDN.

       UML_BUILDRESULT=/directory/of/build/result
	      The directory where build result of pbuilder-user-mode-linux is stored.

       ROOTSTRAP_IMAGESIZE=size-in-megabytes
	      The size, in MB, of the disk iamge to create. Defaults to 1000.

NOTES

       It is advised to set APTCACHEHARDLINK to no in ~/.pbuilderrc.  see pbuilderrc(5) for details.

AUTHOR

       Initial coding, and main maintenance is done by Junichi Uekawa <dancer@debian.org>.

       The homepage is available at http://pbuilder.alioth.debian.org

FILES

       /etc/pbuilder/pbuilder-uml.conf, ${HOME}/.pbuilderrc

SEE ALSO

       /usr/share/doc/pbuilder/pbuilder-doc.html, pbuilder-user-mode-linux(1), pbuilder(8), pbuilderrc(5), pdebuild(1)

Debian								    2003 Jan 8						      pbuilder-uml.conf(5)