10-13-2009
Putty in raw mode dosen't do it. I can use screen /dev/remserial1 and that works fine. I think I need to specify the baud rate and comm settings of the virtual device.
9 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
hi. Im trying to install a switch.
And the manual says i should type a command including a SerialPortDevicePath. which is the filepath to serial port used for connection.
However.. nothing about how to find this info.
Could anyone help me where to find this path?
thx
mr.T (6 Replies)
Discussion started by: tyskertøs
6 Replies
2. AIX
I have installed aix 5.2 on aix box through serial console connected to COM 1 . I even get a login prompt after the fresh installation . But as soon as i give a root & enter i again get a login prompt.i..e I am not able to logon after a fresh installation.
and even i configured IP configuration... (0 Replies)
Discussion started by: linuxnightowl84
0 Replies
3. Programming
I am trying to access DG-100 gps logger on Mac OS X with POSIX API. The device uses a Prolific usb-serial controller, and connect to the usb port on my mac.
After I install the Prolific driver, it shows up as /dev/tty.usbserial and /dev/cu.usbserial. The vendor has published the data format. So... (1 Reply)
Discussion started by: monkeybiz
1 Replies
4. Linux
Hey!
I'm trying to figure out a sollution for a problem I have at my company with an Iomega MiniMax 500 GB USB disk.
If i run cat /proc/bus/usb/devices
I get this information:
T: Bus=01 Lev=02 Prnt=04 Port=00 Cnt=01 Dev#= 5 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00... (2 Replies)
Discussion started by: noratx
2 Replies
5. Solaris
Hi community,
I've currently working on SUN Server V490 and I'm connecting with a Serial port (I DON'T HAVE ANY IP CONNECTIVITY)...I need to redirect the graphic interface of Oracle with the dbca command; I know a way with an IP Connectivity ( use a X-Server and then setenv DISPLAY... (7 Replies)
Discussion started by: Sunb3
7 Replies
6. Programming
I have problem with C programming. I want to send & receive data through serial communication. I send data(command) to device to get data from device but when receive data, it can't get altogether of data.
It get only some data. What should I do to get altogether of data?
If all of... (7 Replies)
Discussion started by: noppon_s
7 Replies
7. Windows & DOS: Issues & Discussions
Hello all.
I have an old computer with M$-DOS 7. I want to use it like a dumb terminal, with telnet. I need to connect it to my desktop These are my questions:
How can i configure the serial port on dos?
How can i telnet form dos to the serial port?
How can i set up a telnet server on the... (12 Replies)
Discussion started by: mghis
12 Replies
8. SCO
I am trying to change one of my serial printers from /dev/ttyr002 to /dev/ttyr014:
lpstat -s
device for check3: /dev/ttyr002
device for check4: /dev/ttyr002
I changed the tty setting for check3 in:
/etc/printcap
/var/spool/lp/admins/lp/printers/check3
to /dev/ttyr014
Then I get:... (4 Replies)
Discussion started by: herot
4 Replies
9. Shell Programming and Scripting
I'm new to Linux (Ubuntu 16.04), and very new to BASH scripting. I have a Numato 8-channel USB GPIO device, which is a DAQ that appears in the system as a serial port. In Linux it appears as ttyACM0. I can easily manipulate a GPO with, for example:
echo "gpio set 7" > /dev/ttyACM0
...followed... (12 Replies)
Discussion started by: Chalk-X
12 Replies