hi. Im trying to install a switch.
And the manual says i should type a command including a SerialPortDevicePath. which is the filepath to serial port used for connection.
However.. nothing about how to find this info.
Could anyone help me where to find this path?
thx
mr.T (6 Replies)
I have installed aix 5.2 on aix box through serial console connected to COM 1 . I even get a login prompt after the fresh installation . But as soon as i give a root & enter i again get a login prompt.i..e I am not able to logon after a fresh installation.
and even i configured IP configuration... (0 Replies)
I am trying to access DG-100 gps logger on Mac OS X with POSIX API. The device uses a Prolific usb-serial controller, and connect to the usb port on my mac.
After I install the Prolific driver, it shows up as /dev/tty.usbserial and /dev/cu.usbserial. The vendor has published the data format. So... (1 Reply)
Hey!
I'm trying to figure out a sollution for a problem I have at my company with an Iomega MiniMax 500 GB USB disk.
If i run cat /proc/bus/usb/devices
I get this information:
T: Bus=01 Lev=02 Prnt=04 Port=00 Cnt=01 Dev#= 5 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00... (2 Replies)
Hi community,
I've currently working on SUN Server V490 and I'm connecting with a Serial port (I DON'T HAVE ANY IP CONNECTIVITY)...I need to redirect the graphic interface of Oracle with the dbca command; I know a way with an IP Connectivity ( use a X-Server and then setenv DISPLAY... (7 Replies)
I have problem with C programming. I want to send & receive data through serial communication. I send data(command) to device to get data from device but when receive data, it can't get altogether of data.
It get only some data. What should I do to get altogether of data?
If all of... (7 Replies)
Hello all.
I have an old computer with M$-DOS 7. I want to use it like a dumb terminal, with telnet. I need to connect it to my desktop These are my questions:
How can i configure the serial port on dos?
How can i telnet form dos to the serial port?
How can i set up a telnet server on the... (12 Replies)
I am trying to change one of my serial printers from /dev/ttyr002 to /dev/ttyr014:
lpstat -s
device for check3: /dev/ttyr002
device for check4: /dev/ttyr002
I changed the tty setting for check3 in:
/etc/printcap
/var/spool/lp/admins/lp/printers/check3
to /dev/ttyr014
Then I get:... (4 Replies)
I'm new to Linux (Ubuntu 16.04), and very new to BASH scripting. I have a Numato 8-channel USB GPIO device, which is a DAQ that appears in the system as a serial port. In Linux it appears as ttyACM0. I can easily manipulate a GPO with, for example:
echo "gpio set 7" > /dev/ttyACM0
...followed... (12 Replies)
Discussion started by: Chalk-X
12 Replies
LEARN ABOUT SUSE
reader.conf
READER.CONF(5) PC/SC Lite READER.CONF(5)NAME
reader.conf - configuration file for pcscd readers' drivers
DESCRIPTION
The /etc/reader.conf file contains configuration information for serial and (some) PCMCIA smart card readers.
USB readers SHALL NOT be configured using this file. pcscd uses another mechanism to automatically load USB drivers.
SYNTAX
The /etc/reader.conf is a regular text file. Each reader must be defined by four fields:
FRIENDLYNAME TEXT_STRING
DEVICENAME FILENAME
LIBPATH FILENAME
CHANNELID NUMBER
The "FRIENDLYNAME" field is an arbitrary text used to identify the reader. This text is displayed by commands like pcsc_scan(1) that prints
the names of all the connected and detected readers.
The "DEVICENAME" field was not used for old drivers (using the IFD handler version 2.0 or earlier). It is now (IFD handler version 3.0)
used to identify the physical port on which the reader is connected. This is the device name of this port. It is dependent of the OS ker-
nel. The first serial port device is called /dev/ttyS0 under Linux and /dev/cuaa0 under FreeBSD.
The "LIBPATH" field is the filename of the driver code. The driver is a dynamically loaded piece of code (generally a drivername.so*file).
The "CHANNELID" is no more used for recent drivers (IFD handler 3.0) and has been superseded by "DEVICENAME". If you have an old driver
this field is used to indicate the port to use. You should read your driver documentation to know what information is needed here. It
should be the serial port number for a serial reader.
EXAMPLE
# Gemplus GemPCTwin reader with serial communication
# connected to the first serial port
FRIENDLYNAME "GemPCTwin serial"
DEVICENAME /dev/ttyS0
LIBPATH /usr/lib64/readers/serial/libccidtwin.so.0.4.1
CHANNELID 1
DEBUGGING
In order to set up your /etc/reader.conf file correctly you may want to have debug messages from pcscd. I recommend you to start pscsd in
the foreground and debug mode using:
# pcscd --foreground --debug
If everything seems OK you can use the pcsc_scan command to print the list of correctly detected readers and try to get the ATR of your
smart cards.
AUTHOR
Ludovic Rousseau <ludovic.rousseau@free.fr>
SEE ALSO pcscd(8), pcsc_scan(1)Muscle August 2005 READER.CONF(5)
10-12-2009
