hi. Im trying to install a switch.
And the manual says i should type a command including a SerialPortDevicePath. which is the filepath to serial port used for connection.
However.. nothing about how to find this info.
Could anyone help me where to find this path?
thx
mr.T (6 Replies)
I have installed aix 5.2 on aix box through serial console connected to COM 1 . I even get a login prompt after the fresh installation . But as soon as i give a root & enter i again get a login prompt.i..e I am not able to logon after a fresh installation.
and even i configured IP configuration... (0 Replies)
I am trying to access DG-100 gps logger on Mac OS X with POSIX API. The device uses a Prolific usb-serial controller, and connect to the usb port on my mac.
After I install the Prolific driver, it shows up as /dev/tty.usbserial and /dev/cu.usbserial. The vendor has published the data format. So... (1 Reply)
Hey!
I'm trying to figure out a sollution for a problem I have at my company with an Iomega MiniMax 500 GB USB disk.
If i run cat /proc/bus/usb/devices
I get this information:
T: Bus=01 Lev=02 Prnt=04 Port=00 Cnt=01 Dev#= 5 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00... (2 Replies)
Hi community,
I've currently working on SUN Server V490 and I'm connecting with a Serial port (I DON'T HAVE ANY IP CONNECTIVITY)...I need to redirect the graphic interface of Oracle with the dbca command; I know a way with an IP Connectivity ( use a X-Server and then setenv DISPLAY... (7 Replies)
I have problem with C programming. I want to send & receive data through serial communication. I send data(command) to device to get data from device but when receive data, it can't get altogether of data.
It get only some data. What should I do to get altogether of data?
If all of... (7 Replies)
Hello all.
I have an old computer with M$-DOS 7. I want to use it like a dumb terminal, with telnet. I need to connect it to my desktop These are my questions:
How can i configure the serial port on dos?
How can i telnet form dos to the serial port?
How can i set up a telnet server on the... (12 Replies)
I am trying to change one of my serial printers from /dev/ttyr002 to /dev/ttyr014:
lpstat -s
device for check3: /dev/ttyr002
device for check4: /dev/ttyr002
I changed the tty setting for check3 in:
/etc/printcap
/var/spool/lp/admins/lp/printers/check3
to /dev/ttyr014
Then I get:... (4 Replies)
I'm new to Linux (Ubuntu 16.04), and very new to BASH scripting. I have a Numato 8-channel USB GPIO device, which is a DAQ that appears in the system as a serial port. In Linux it appears as ttyACM0. I can easily manipulate a GPO with, for example:
echo "gpio set 7" > /dev/ttyACM0
...followed... (12 Replies)
Discussion started by: Chalk-X
12 Replies
LEARN ABOUT DEBIAN
plink
plink(1) PuTTY tool suite plink(1)NAME
plink - PuTTY link, command line network connection tool
SYNOPSIS
plink [options] [user@]host [command]
DESCRIPTION
plink is a network connection tool supporting several protocols.
OPTIONS
The command-line options supported by plink are:
-V Show version information and exit.
-pgpfp Display the fingerprints of the PuTTY PGP Master Keys and exit, to aid in verifying new files released by the PuTTY team.
-v Show verbose messages.
-load session
Load settings from saved session.
-ssh Force use of SSH protocol (default).
-telnet
Force use of Telnet protocol.
-rlogin
Force use of rlogin protocol.
-raw Force raw mode.
-serial
Force serial mode.
-P port
Connect to port port.
-l user
Set remote username to user.
-m path
Read remote command(s) from local file path.
-batch Disable interactive prompts.
-pw password
Set remote password to password. CAUTION: this will likely make the password visible to other users of the local machine (via com-
mands such as `w').
-L [srcaddr:]srcport:desthost:destport
Set up a local port forwarding: listen on srcport (or srcaddr:srcport if specified), and forward any connections over the SSH con-
nection to the destination address desthost:destport. Only works in SSH.
-R [srcaddr:]srcport:desthost:destport
Set up a remote port forwarding: ask the SSH server to listen on srcport (or srcaddr:srcport if specified), and to forward any con-
nections back over the SSH connection where the client will pass them on to the destination address desthost:destport. Only works in
SSH.
-D [srcaddr:]srcport
Set up dynamic port forwarding. The client listens on srcport (or srcaddr:srcport if specified), and implements a SOCKS server. So
you can point SOCKS-aware applications at this port and they will automatically use the SSH connection to tunnel all their connec-
tions. Only works in SSH.
-X Enable X11 forwarding.
-x Disable X11 forwarding (default).
-A Enable agent forwarding.
-a Disable agent forwarding (default).
-t Enable pty allocation (default if a command is NOT specified).
-T Disable pty allocation (default if a command is specified).
-1 Force use of SSH protocol version 1.
-2 Force use of SSH protocol version 2.
-C Enable SSH compression.
-i path
Private key file for authentication.
-s Remote command is SSH subsystem (SSH-2 only).
-N Don't start a remote command or shell at all (SSH-2 only).
-sercfg configuration-string
Specify the configuration parameters for the serial port, in -serial mode. configuration-string should be a comma-separated list of
configuration parameters as follows:
o Any single digit from 5 to 9 sets the number of data bits.
o `1', `1.5' or `2' sets the number of stop bits.
o Any other numeric string is interpreted as a baud rate.
o A single lower-case letter specifies the parity: `n' for none, `o' for odd, `e' for even, `m' for mark and `s' for space.
o A single upper-case letter specifies the flow control: `N' for none, `X' for XON/XOFF, `R' for RTS/CTS and `D' for DSR/DTR.
MORE INFORMATION
For more information on plink, it's probably best to go and look at the manual on the PuTTY web page:
http://www.chiark.greenend.org.uk/~sgtatham/putty/
BUGS
This man page isn't terribly complete. See the above web link for better documentation.
PuTTY tool suite 2004-03-24 plink(1)