hi. Im trying to install a switch.
And the manual says i should type a command including a SerialPortDevicePath. which is the filepath to serial port used for connection.
However.. nothing about how to find this info.
Could anyone help me where to find this path?
thx
mr.T (6 Replies)
I have installed aix 5.2 on aix box through serial console connected to COM 1 . I even get a login prompt after the fresh installation . But as soon as i give a root & enter i again get a login prompt.i..e I am not able to logon after a fresh installation.
and even i configured IP configuration... (0 Replies)
I am trying to access DG-100 gps logger on Mac OS X with POSIX API. The device uses a Prolific usb-serial controller, and connect to the usb port on my mac.
After I install the Prolific driver, it shows up as /dev/tty.usbserial and /dev/cu.usbserial. The vendor has published the data format. So... (1 Reply)
Hey!
I'm trying to figure out a sollution for a problem I have at my company with an Iomega MiniMax 500 GB USB disk.
If i run cat /proc/bus/usb/devices
I get this information:
T: Bus=01 Lev=02 Prnt=04 Port=00 Cnt=01 Dev#= 5 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00... (2 Replies)
Hi community,
I've currently working on SUN Server V490 and I'm connecting with a Serial port (I DON'T HAVE ANY IP CONNECTIVITY)...I need to redirect the graphic interface of Oracle with the dbca command; I know a way with an IP Connectivity ( use a X-Server and then setenv DISPLAY... (7 Replies)
I have problem with C programming. I want to send & receive data through serial communication. I send data(command) to device to get data from device but when receive data, it can't get altogether of data.
It get only some data. What should I do to get altogether of data?
If all of... (7 Replies)
Hello all.
I have an old computer with M$-DOS 7. I want to use it like a dumb terminal, with telnet. I need to connect it to my desktop These are my questions:
How can i configure the serial port on dos?
How can i telnet form dos to the serial port?
How can i set up a telnet server on the... (12 Replies)
I am trying to change one of my serial printers from /dev/ttyr002 to /dev/ttyr014:
lpstat -s
device for check3: /dev/ttyr002
device for check4: /dev/ttyr002
I changed the tty setting for check3 in:
/etc/printcap
/var/spool/lp/admins/lp/printers/check3
to /dev/ttyr014
Then I get:... (4 Replies)
I'm new to Linux (Ubuntu 16.04), and very new to BASH scripting. I have a Numato 8-channel USB GPIO device, which is a DAQ that appears in the system as a serial port. In Linux it appears as ttyACM0. I can easily manipulate a GPO with, for example:
echo "gpio set 7" > /dev/ttyACM0
...followed... (12 Replies)
Discussion started by: Chalk-X
12 Replies
LEARN ABOUT REDHAT
serial_cs
SERIAL_CS(4) Kernel Interfaces Manual SERIAL_CS(4)NAME
serial_cs - PCMCIA serial port driver
SYNOPSIS
insmod serial_cs.o [pc_debug=n] [irq_list=i,j,...] [do_sound=n]
DESCRIPTION
Serial_cs is the Card Services driver for all PCMCIA serial devices, including modem cards. When serial_cs is bound to a serial or modem
card, it will generally attempt to allocate the first unused serial device for use by the card. The device chosen will be recorded in the
kernel log file, and will also be reported to cardmgr(8). The major and minor numbers and device name reported by serial_cs will match the
corresponding "dialout" device (/dev/cua#). The new device can be accessed using this device file or the corresponding /dev/ttyS# device.
The default serial card setup script will link the dialout device to /dev/modem.
PARAMETERS
pc_debug=n
Selects the PCMCIA debugging level. This parameter is only available if the module is compiled with debugging enabled. A non-zero
value enables debugging.
irq_list=i,j,...
Specifies the set of interrupts that may be allocated by this driver.
do_sound=n
A flag specifying if speaker output should be enabled. The default is 1 (true). Set to 0 to disable speaker output.
AUTHOR
David Hinds - dahinds@users.sourceforge.net
SEE ALSO cardmgr(8), pcmcia(5).
pcmcia-cs 2000/06/12 21:24:48 SERIAL_CS(4)