10-09-2009
A lot! In some times more than 400 PCs & servers.
I've 2 other servers which work fine but 2 of my servers have this problem.
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hi !
Does anyone know how can i get information about my network interface ... if it works in half or full duplex mode !!
Thx in adivance !
Witt (4 Replies)
Discussion started by: witt
4 Replies
2. Gentoo
Hi all,
I'm trying to write a script that will turn off the network interface eth0 on a linux Gentoo machine and then turn it back on, any help?
Thanks,
Neked (1 Reply)
Discussion started by: neked
1 Replies
3. Solaris
Hi All,
I want to configure network into my system.
i tried following in to configure the interface
to find the name of interface
#prtdiag |grep net
i got following
0 PCI-1 33 1 network-SUNW, hme
then i tried following
#prtconf -v |grep net
network, instance #0 (6 Replies)
Discussion started by: kumarmani
6 Replies
4. Solaris
i need to configure a zone to use different interface (bge2) than global and have connected to completely different network switch & to use its own defaultrouter and hosts file .. is it possible ..if so ..how ?
Thanks (9 Replies)
Discussion started by: skamal4u
9 Replies
5. UNIX and Linux Applications
Hi,
I'm a italian student. For my thesis I develop a gateway with protocol 6lowpan.
For that I must access to network interface to develope my personal stack based on standard 802.15.4.
Can you help me? I need an explanation for that. (0 Replies)
Discussion started by: berny88
0 Replies
6. IP Networking
Hello,
Please what's the difference between:
AND
Thank you so much (3 Replies)
Discussion started by: chercheur857
3 Replies
7. IP Networking
Hello,
Please, how can i create a network interface with a routable IP address on linux (ubuntu) ?
AND
How can i desactivate an interface?
Thank you so much for help. (1 Reply)
Discussion started by: chercheur857
1 Replies
8. Solaris
I've one Netra 240
After changing main board and system configuration card reader, Network is not accessible any more, Network interfaces are always UP and Running even when there is no cable connected to Network interfaces.
I tried to restart and plumb/unplumb with no luck.
ifconfig -a... (7 Replies)
Discussion started by: samer.odeh
7 Replies
9. Solaris
Hi all, I'm new here and looking for some help.
I'm looking for the way to rename the network interfaces for Solaris 10. Got a server with 2 network cards (say "igb0" and "igb1") and there were some reasons that I have to swap the pci slots for those cards. However, after I did that, Solaris 10... (3 Replies)
Discussion started by: bbq9
3 Replies
10. UNIX for Dummies Questions & Answers
I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Discussion started by: westmoreland
1 Replies
LEARN ABOUT OPENSOLARIS
bvnc
bssh/bvnc/bshell(1) General Commands Manual bssh/bvnc/bshell(1)
NAME
bssh/bvnc/bshell - Browse for SSH/VNC servers on the local network
SYNOPSIS
bssh
bvnc
bshell
DESCRIPTION
bssh/bvnc/bshell browses for SSH/VNC servers on the local network, shows them in a GUI for the user to select one and finally calls
ssh/vncviewer after a selection was made.
If the binary is called as bssh only ssh servers will be shown. If the binary is called as bvnc only VNC servers will be shown. If the
binary is called as bshell both VNC and SSH servers are shown.
OPTIONS
-s | --ssh
Browse for SSH servers (and only SSH servers) regardless under which name the binary is called.
-v | --vnc
Browse for VNC servers (and only VNC servers) regardless under which name the binary is called.
-S | --shell
Browse for both VNC and SSH servers regardless under which name the binary is called.
-d | --domain= DOMAIN
Browse in the specified domain. If omitted bssh/bvnc/bshell will browse in the default browsing domain (usually .local)
-h | --help
Show help.
SEE ALSO
avahi-browse(1), ssh(1), vncviewer(1)
COMMENTS
This man page was written using xml2man(1) by Oliver Kurth.
Manuals User bssh/bvnc/bshell(1)