10-08-2009
Bring NIC in Promiscious Mode
Hello,
I have windows 2000 on my pc and in order to capture network traffic it is required to to bring the NIC into promiscious mode.
Can any one please guide me what is required to achieve it?
thanks in advance.
8 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Right now I have a computer that I want to use as the monitor for my network. It's currently running Windows 7, and so as I understand it the NIC won't monitor all the traffic on the network. So my question is, if I install Linux on this computer will I be able to force the NIC card into... (1 Reply)
Discussion started by: iJeydon
1 Replies
2. UNIX for Advanced & Expert Users
Hi, all:
The physical network interface card should drop the packets if it doesn't match the MAC address of the NIC. In my PC, however, the packets which shoud be dropped trigger the interrupt function of my own driver and are recieved as skb to be transfered to the upper layer!
Why? How... (1 Reply)
Discussion started by: liklstar
1 Replies
3. Solaris
I couldn't install my nic in solaris 10. I compiled and added
the driver but failed to attach the driver and ifconfig output
shows only loopback dev. Please see the following output and tell
me whether my nic has been detected and why the driver failed to
attach?
My nic is detected in linux... (0 Replies)
Discussion started by: vectrum
0 Replies
4. IP Networking
I am new in squid proxy.
My question is how to (and if it's necessary) to set one NIC for inbound traffic (http requests) and one NIC for outbound traffic (http answers)?
Thank you in advance! (4 Replies)
Discussion started by: aixlover
4 Replies
5. Solaris
:confused:
when i tried to look the status of DNS-client, it is in maintenance mode.....
Please tell me how to bring it back to online mode...PLEASE TELL ME STEP BY STEP.... PLEASE...
:wall: (2 Replies)
Discussion started by: vamshigvk475
2 Replies
6. Red Hat
Dear All
I want tune my NIC's rps, rfs and xps value.
In my system I have two NIC (eth0, eth1) and I have a bond0 ( eth0, eth1).
Here is the question? Which device should I modify ?
eth0 and eth1? or just modify bond0 or modify all device (eth0, eth1, bond0)
Any advice is welcome.... (0 Replies)
Discussion started by: nnnnnnine
0 Replies
7. HP-UX
is there a way for my C++ application to find out which mode the hpux OS is running in?
standard mode or trusted mode. (3 Replies)
Discussion started by: einsteinBrain
3 Replies
8. Linux
Hello Admins,
My ask is how can I add two different subnet IPs to same box with two different gateways?
The issue is I can connect to the box when I am on ethernet LAN, but I am not able to connect to the same IP when I am on wifi. The server is RHEL 7 VM on vmware.
How can I get connected... (4 Replies)
Discussion started by: snchaudhari2
4 Replies
LEARN ABOUT NETBSD
eshconfig
ESHCONFIG(8) BSD System Manager's Manual ESHCONFIG(8)
NAME
eshconfig -- configure Essential Communications' HIPPI network interface
SYNOPSIS
eshconfig [-estx] [-b bytes] [-c bytes] [-d filename] [-i usecs] [-m bytes] [-r bytes] [-u filename] [-w bytes] [interface]
DESCRIPTION
eshconfig is used to configure device-specific parameters and download new firmware to the Essential Communications RoadRunner-based HIPPI
network interface. The interface is very sensitive to the DMA performance characteristics of the host, and so requires careful tuning to
achieve reasonable performance. In addition, firmware is likely to change frequently, which necessitates a reasonably easy way to update
that firmware.
Available operands for eshconfig:
-b bytes
Adjust the burst size for read (by NIC of host memory) DMA.
-c bytes
Adjust the burst size for write (by NIC of host memory) DMA.
-d filename
Filename for file to download into NIC firmware. This must be a file in the standard Essential format, with :04 preceding every
line, and a tag line at the end indicating the characteristics of the firmware file.
-e Write data to EEPROM. Normally, setting tuning parameters will only persist until the system is rebooted. Setting this parameter
ensures that the changes will be written to EEPROM.
-i usecs
Interrupt delay in microseconds.
-m bytes
Minimum number of bytes to DMA in one direction (read or write) before allowing a DMA in the other direction. Tuning this prevents
one direction from dominating the flow of bytes, and artificially throttling the NIC.
-r bytes
Bytes before DMA starts for read (from host to NIC). This controls how soon the DMA is triggered; until this many bytes are
requested, the DMA will not begin.
-s Show statistics for the HIPPI NIC. Repeat the option to suppress non-zero statistics.
-t Show current tuning parameters on the host.
-u filename
Name of file to which the NIC firmware should be uploaded. Not currently supported.
-w bytes
Number of bytes required before write (from NIC to host) DMA is started. Until this many bytes are ready to be written, the DMA will
not start.
-x Reset the NIC. This is necessary for the HIPPI-FP support, as ifconfig(8) will no longer physically reset the NIC when the inter-
faces goes up and down.
Only the super-user may modify the configuration of a network interface.
DIAGNOSTICS
Messages indicating the specified interface does not exist or the user is not privileged and tried to alter an interface's configuration.
SEE ALSO
esh(4), ifconfig(8)
HISTORY
The eshconfig command first appeared in NetBSD 1.4.
BSD
June 17, 2005 BSD