Hi folks!
i've just downloaded the three SOlaris 8 Free install-CDs, then went to install it in a VM on VMware 2.0.3, okay DCA and CD inserted, DCA configured all devices - THEN
at the selection of the boot device - selected CD - getting DISK READ ERROR at sector 120.
Can anyone help?!!!... (1 Reply)
WEe have installed Intel version of Solaris 8 in a machine .we skipped the network configuration at the begning.we selected unnetworked.Now we need to connect the same machine to a network.
We configured the Card using ifconfig but its taking the ip address itself as the Default G/W.
I need help... (4 Replies)
hello
i had soloaris 8 installed . at the beggining it sees my network
card( intel i815/82559 onboard)(my mainboard is GA-8IRXP);
but during the installation when I fill the ip address and the dns
at the end that i should confirm it says:
no dns find (i'm sure about the dns... (4 Replies)
Hi all,
I tried to install Solaris 10 and then VMware ESX server v3.02 on the same PC (or hard drive). But after successfully installing Solaris 10, when I installed Vmware ESX Server on the same drive(but on different partition, boot menu is not coming.
It is just booting Vmware only.
Pls... (1 Reply)
I am running solaris 10 on VMware and I do not know how to setup the USB drive. After refer to few doc from sun still unable to get what i should do.
Can someone help?
On VMware I have added a USB controller.
Oh yes, from prtconf and dmesg, it don't seem to reganize the usb controller. I... (0 Replies)
Hi there,
I run a SunFire v245 with solaris 10. I run a custom ERP on that. my clients are connecting via telnet and run the application...
my last "server" was a sun blade 100 with solaris 8, everything was running correctly.
Since I have the new server, I have many problem with my... (5 Replies)
Hi all,
I have install sun solaris 10 on vmware server and i cant ping the solaris guest machine from the host and vice versa.
The enable network card in the host machine is an wifi card so I know that i can't use bridged network from Vmware.
I tried to use host or NAT but it seem not to work... (1 Reply)
Hi All,
We have configured an hp network printer on a Solaris-sparc machine.
We are unable to print any files from this machine.
The following are the other details:
lpstat -p hpnic -l
printer hpnic waiting for auto-retry. available.
exec exit fault
Form mounted:
... (0 Replies)
I am going to take up a position in Data & Network Security.
I would need to write network shell scripts doing the following task:
Going to around 2000 servers and findout which groups has access to each servers and which ids are there in each group that has access.
I need to implement... (1 Reply)
Hello all, thanks for reading my question:
So I've been a Unix/Linux SysAdmin for a couple years, and I'm a bit over my head running solo, trying to set up LDoms using Oracle VM Server 3.1 for SPARC. I've been very careful, and things have gone well up until the point I try to access the new... (9 Replies)
Discussion started by: Lyxix
9 Replies
LEARN ABOUT SUSE
irsend
IRSEND(1) FSF IRSEND(1)NAME
irsend - basic LIRC program to send infra-red commands
SYNOPSIS
irsend [options] DIRECTIVE REMOTE CODE [CODE...]
DESCRIPTION
Asks the lircd daemon to send one or more CIR (Consumer Infra-Red) commands. This is intended for remote control of electronic devices such
as TV boxes, HiFi sets, etc.
DIRECTIVE can be:
SEND_ONCE - send CODE [CODE ...] once
SEND_START - start repeating CODE
SEND_STOP - stop repeating CODE
LIST - list configured remote items
SET_TRANSMITTERS - set transmitters NUM [NUM ...]
SIMULATE - simulate IR event
REMOTE is the name of a remote, as described in the lircd configuration file.
CODE is the name of a remote control key of REMOTE, as it appears in the lircd configuration file.
NUM is the transmitter number of the hardware device.
For the LIST DIRECTIVE, REMOTE and/or CODE can be empty:
LIST "" "" - list all configured remote names
LIST REMOTE "" - list all codes of REMOTE
LIST REMOTE CODE - list only CODE of REMOTE
The SIMULATE command only works if it has been explicitly enabled in lircd.
-h --help
display usage summary
-v --version
display version
-d --device
use given lircd socket [/var/run/lirc/lircd]
-a --address=host[:port]
connect to lircd at this address
-# --count=n
send command n times
EXAMPLES
irsend LIST DenonTuner ""
irsend SEND_ONCE DenonTuner PROG-SCAN
irsend SEND_ONCE OnkyoAmpli VOL-UP VOL-UP VOL-UP VOL-UP
irsend SEND_START OnkyoAmpli VOL-DOWN ; sleep 3
irsend SEND_STOP OnkyoAmpli VOL-DOWN
irsend SET_TRANSMITTERS 1
irsend SET_TRANSMITTERS 1 3 4
irsend SIMULATE "0000000000000476 00 OK TECHNISAT_ST3004S"
FILES
/etc/lirc/lircd.conf
Default lircd configuration file. It should contain all the remotes, their infra-red codes and the corresponding timing and wave-
form details.
DIAGNOSTICS
If lircd is not running (or /var/run/lirc/lircd lacks write permissions) irsend aborts with the following diagnostics:
"irsend: could not connect to socket"
"irsend: Connection refused" (or "Permission denied").
SEE ALSO
The documentation for lirc is maintained as html pages. They are located under html/ in the documentation directory.
lircd(8), mode2(1), smode2(1), xmode2(1), irrecord(1), irw(1), http://www.lirc.org.
irsend 0.8.7pre1 May 2010 IRSEND(1)