Hi folks!
i've just downloaded the three SOlaris 8 Free install-CDs, then went to install it in a VM on VMware 2.0.3, okay DCA and CD inserted, DCA configured all devices - THEN
at the selection of the boot device - selected CD - getting DISK READ ERROR at sector 120.
Can anyone help?!!!... (1 Reply)
WEe have installed Intel version of Solaris 8 in a machine .we skipped the network configuration at the begning.we selected unnetworked.Now we need to connect the same machine to a network.
We configured the Card using ifconfig but its taking the ip address itself as the Default G/W.
I need help... (4 Replies)
hello
i had soloaris 8 installed . at the beggining it sees my network
card( intel i815/82559 onboard)(my mainboard is GA-8IRXP);
but during the installation when I fill the ip address and the dns
at the end that i should confirm it says:
no dns find (i'm sure about the dns... (4 Replies)
Hi all,
I tried to install Solaris 10 and then VMware ESX server v3.02 on the same PC (or hard drive). But after successfully installing Solaris 10, when I installed Vmware ESX Server on the same drive(but on different partition, boot menu is not coming.
It is just booting Vmware only.
Pls... (1 Reply)
I am running solaris 10 on VMware and I do not know how to setup the USB drive. After refer to few doc from sun still unable to get what i should do.
Can someone help?
On VMware I have added a USB controller.
Oh yes, from prtconf and dmesg, it don't seem to reganize the usb controller. I... (0 Replies)
Hi there,
I run a SunFire v245 with solaris 10. I run a custom ERP on that. my clients are connecting via telnet and run the application...
my last "server" was a sun blade 100 with solaris 8, everything was running correctly.
Since I have the new server, I have many problem with my... (5 Replies)
Hi all,
I have install sun solaris 10 on vmware server and i cant ping the solaris guest machine from the host and vice versa.
The enable network card in the host machine is an wifi card so I know that i can't use bridged network from Vmware.
I tried to use host or NAT but it seem not to work... (1 Reply)
Hi All,
We have configured an hp network printer on a Solaris-sparc machine.
We are unable to print any files from this machine.
The following are the other details:
lpstat -p hpnic -l
printer hpnic waiting for auto-retry. available.
exec exit fault
Form mounted:
... (0 Replies)
I am going to take up a position in Data & Network Security.
I would need to write network shell scripts doing the following task:
Going to around 2000 servers and findout which groups has access to each servers and which ids are there in each group that has access.
I need to implement... (1 Reply)
Hello all, thanks for reading my question:
So I've been a Unix/Linux SysAdmin for a couple years, and I'm a bit over my head running solo, trying to set up LDoms using Oracle VM Server 3.1 for SPARC. I've been very careful, and things have gone well up until the point I try to access the new... (9 Replies)
Discussion started by: Lyxix
9 Replies
LEARN ABOUT DEBIAN
tgt-setup-lun
tgt-setup-lun(8) System Manager's Manual tgt-setup-lun(8)NAME
tgt-setup-lun - creates a target, adds a device to the target and defines initiators that can connect to the target
SYNOPSIS
tgt-setup-lun -d device -n target_name [initiator_IP1 initiator_IP2 ...] [-h]
DESCRIPTION
Starts tgtd if necessary and creates a target according to the supplied target_name. The format of the target name is as follows:
iqn.2001-04.com.<hostname>-<target_name> The target name must be unique.
The script then adds the requested device to the target. If specific IP addresses are defined, it adds them to the list of allowed initia-
tors for that target. If no IP addresses is defined, it defines that the target accepts any initiator.
EXAMPLES
Create a target that uses /dev/sdb1 and allows connections only from 192.168.10.81:
tgt-setup-lun -d /dev/sdb1 -n my_target 192.168.10.81
Create a target that uses /dev/sdb1 and allows connections only from 192.168.10.81 and 192.168.10.82:
tgt-setup-lun -d /dev/sdb1 -n my_target 192.168.10.81 192.168.10.82
Create a target that uses /dev/sdb1 and allows connections from any initiator:
tgt-setup-lun -d /dev/sdb1 -n my_target
Display help:
tgt-setup-lun -h
AUTHOR
Written by Erez Zilber
REPORTING BUGS
Report bugs to <stgt@vger.kernel.org>
COPYRIGHT
Copyright (C) Voltaire Ltd. 2008.
tgt-setup-lun(8)