All,
How do you set a Solaris 9 server which received ntp updates from a ntp server to broadcast them on a local subnet. I have created a /etc/inet/ntp.conf file to receive the updates from a server on network and need to make this server become like a ntp relay from the main server.
Any... (1 Reply)
Hi folks,
The server time is no tgetiing synched up with the NTP server.
I tried ntpdate -u <ipadress> this is not working. please help out.
regards,
Sag. (7 Replies)
Hello all,
What would be the most convienint and proper way on syncing up the time and date on Solaris 8 servers with an NTP server?
Any help would be appreciated. Thanks (2 Replies)
Ok, I have 4 production systems. There is one NTP server for all four systems. In each system there is one Solaris 10 box that points to that NTP server. All of the other machines in the system point to the Solaris 10 machine to get their time sync.
All four Solaris 10 machines have essentially... (2 Replies)
Hi,
I have 4 machines and all are NTP configured with same ntp.conf file. But 3 machines are in sync with Time server and 4th machine is not contacting & sync with the NTP server. Please see the below details.
# service ntpd stop
Stopping ntpd: ... (0 Replies)
hi guys
I have several Red Hat 5.7(7) all of them sync time with two NTP Servers based on Windows but the issue is I configure the NTP service, I start the ntp service and use ntpdate -u to set the time the first time
This is what I do
1. Configure /etc/ntp.conf
restrict default kod... (2 Replies)
Hi folks, I have developed a Linux server for my customer. After migrating the server to my customer site, I was trying to sync its time to the NTP time servers at my customer site.
Below is the ntp.conf:
% vi /etc/ntp.conf
# Permit time synchronization with our time source, but do not
# permit... (2 Replies)
We had a network problem a couple of days before that caused 1 interface to down and up. But today I have noticed that our date is wrong, our system have 4 servers and the other 3 are OK.
I used <date> command, the result is: Fri Jan 2 17:57:55 ICT 1970
I have tried set date to be the same as... (3 Replies)
Hi,
I have two ntp servers in my cluster and I want all the nodes in my cluster to sync with either of the ntp servers or just one. Unfortunately it keep rotating the sync, between my ntp server 1, ntp server 2 and local. Is there anyway I can change the sync to avoid local?
# ntpq -p
... (3 Replies)
Discussion started by: pjeedu2247
3 Replies
LEARN ABOUT CENTOS
ntptrace
ntptrace(8) System Manager's Manual ntptrace(8)NAME
ntptrace - trace a chain of NTP servers back to the primary source
SYNOPSIS
ntptrace [ -n ] [ -m maxhosts ] [ server ]
DESCRIPTION
ntptrace is a perl script that uses the ntpq utility program to follow the chain of NTP servers from a given host back to the primary time
source. For ntptrace to work properly, each of these servers must implement the NTP Control and Monitoring Protocol specified in RFC 1305
and enable NTP Mode 6 packets.
If given no arguments, ntptrace starts with localhost. Here is an example of the output from ntptrace:
% ntptrace
localhost: stratum 4, offset 0.0019529, synch distance 0.144135
server2ozo.com: stratum 2, offset 0.0124263, synch distance 0.115784
usndh.edu: stratum 1, offset 0.0019298, synch distance 0.011993, refid 'WWVB'
On each line, the fields are (left to right): the host name, the host stratum, the time offset between that host and the local host (as
measured by ntptrace; this is why it is not always zero for "localhost"), the host synchronization distance, and (only for stratum-1
servers) the reference clock ID. All times are given in seconds. Note that the stratum is the server hop count to the primary source, while
the synchronization distance is the estimated error relative to the primary source. These terms are precisely defined in RFC-1305.
OPTIONS -n Turns off the printing of host names; instead, host IP addresses are given. This may be useful if a nameserver is down.
BUGS
This program makes no attempt to improve accuracy by doing multiple samples.
SEE ALSO ntpd(8)
The official HTML documentation.
This file was automatically generated from HTML source.
ntptrace(8)