All,
How do you set a Solaris 9 server which received ntp updates from a ntp server to broadcast them on a local subnet. I have created a /etc/inet/ntp.conf file to receive the updates from a server on network and need to make this server become like a ntp relay from the main server.
Any... (1 Reply)
Hi folks,
The server time is no tgetiing synched up with the NTP server.
I tried ntpdate -u <ipadress> this is not working. please help out.
regards,
Sag. (7 Replies)
Hello all,
What would be the most convienint and proper way on syncing up the time and date on Solaris 8 servers with an NTP server?
Any help would be appreciated. Thanks (2 Replies)
Ok, I have 4 production systems. There is one NTP server for all four systems. In each system there is one Solaris 10 box that points to that NTP server. All of the other machines in the system point to the Solaris 10 machine to get their time sync.
All four Solaris 10 machines have essentially... (2 Replies)
Hi,
I have 4 machines and all are NTP configured with same ntp.conf file. But 3 machines are in sync with Time server and 4th machine is not contacting & sync with the NTP server. Please see the below details.
# service ntpd stop
Stopping ntpd: ... (0 Replies)
hi guys
I have several Red Hat 5.7(7) all of them sync time with two NTP Servers based on Windows but the issue is I configure the NTP service, I start the ntp service and use ntpdate -u to set the time the first time
This is what I do
1. Configure /etc/ntp.conf
restrict default kod... (2 Replies)
Hi folks, I have developed a Linux server for my customer. After migrating the server to my customer site, I was trying to sync its time to the NTP time servers at my customer site.
Below is the ntp.conf:
% vi /etc/ntp.conf
# Permit time synchronization with our time source, but do not
# permit... (2 Replies)
We had a network problem a couple of days before that caused 1 interface to down and up. But today I have noticed that our date is wrong, our system have 4 servers and the other 3 are OK.
I used <date> command, the result is: Fri Jan 2 17:57:55 ICT 1970
I have tried set date to be the same as... (3 Replies)
Hi,
I have two ntp servers in my cluster and I want all the nodes in my cluster to sync with either of the ntp servers or just one. Unfortunately it keep rotating the sync, between my ntp server 1, ntp server 2 and local. Is there anyway I can change the sync to avoid local?
# ntpq -p
... (3 Replies)
Discussion started by: pjeedu2247
3 Replies
LEARN ABOUT OSF1
timedsetup
timedsetup(8) System Manager's Manual timedsetup(8)NAME
timedsetup - Performs initial setup of the time server daemon (timed).
SYNOPSIS
/usr/sbin/timedsetup
DESCRIPTION
The timedsetup command is an interactive script that can be used to perform initial time service configuration for your system.
By default, timed does not start at boot time. The timedsetup script asks if you want the timed daemon to be started at boot time, and
prompts you for any options to pass to the timed daemon whenever it is invoked. The script then starts the timed daemon.
For more information on the timed options, see the timed(8) reference page.
Note
The timed daemon is provided for compatibility. Tru64 UNIX also provides support for the Network Time Protocol (NTP) through the xntpd
daemon. Compaq recommends you use NTP for time synchronization. If your system is configured to run NTP, the timedsetup command passes
the -E and -M options to the timed daemon by default.
If you plan to run both the timed daemon and NTP, you should configure NTP first.
RESTRICTIONS
In configurations with two or more hosts each connected to the same two or more subnetworks, only one of the host can run the timed with
the -M option.
FILES
Specifies the command pathname The timed startup and shutdown script Specifies timed parameters pertinent to a specific system
SEE ALSO
Commands: timed(8), xntpd(8)timedsetup(8)