10-05-2009
Yes I am sure . Because when this disk went faulty the Os couldnt see the mentioned file system and if it was mirorred this would not happen. More over the fsck command couldnt stat the mentioned file system.
what I did is : I physically pull out the disk and inserted back after 60 seconds, rebooted the system and OS could see the file system again and was able to run fsck to repair the file system.
7 More Discussions You Might Find Interesting
1. Filesystems, Disks and Memory
Hi
I have 2 75GB SCSI hard drives and 2 250GB SATA hard drives which are using RAID Level 1 respectively. I wana have both FTP and Apache installed on them as services. I'm wondering what's the best partitioning schem? I wana use FC3 as my OS, so, I thought I can use the 75GB hard drive as the /... (0 Replies)
Discussion started by: sirbijan
0 Replies
2. UNIX for Dummies Questions & Answers
Anyone know how I can map a windows drive to an apache shared drive?
In my httpd.conf file, I have:
Alias /merc_rpts/ "/u/merc_rpts/"
<Directory "/u/merc_rpts">
Options Indexes
</Directory>
I'm able to bring up a browser and see the contents of this folder.
In... (0 Replies)
Discussion started by: gseyforth
0 Replies
3. SCO
Can anybody help me out to mount USB flash /floppy drive in sco openserver 6.0 . (5 Replies)
Discussion started by: sureshdrajan
5 Replies
4. Shell Programming and Scripting
I have input file like this
Input file:
ABC|abc_etc_passwd
XYZ|XYZ_etc_passwd
zXY|XYZ_etc_passwd
IJK|test_etc_passwd
KLM|test_etc_passwd
i want to do following in a loop.
grep 'ABC' *abc_etc_passwd*
grep 'XYZ' *XYZ_etc_passwd*
grep 'ZXY' *ZXY_etc_passwd*
i have tried this
for i... (2 Replies)
Discussion started by: pinnacle
2 Replies
5. Hardware
I have a 320 GB drive which dual boots Windows and Debian:
Disk /dev/sda: 320.1 GB, 320072933376 bytes
255 heads, 63 sectors/track, 38913 cylinders, total 625142448 sectors
Units = sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal):... (0 Replies)
Discussion started by: phillipsoasis
0 Replies
6. UNIX for Dummies Questions & Answers
Hi Guys,
Can any one help me on this.
I need help to move .csv/.xls file from unix path to windows shared drive or c:\ drive?
Regards,
LKR (1 Reply)
Discussion started by: lakshmanraok117
1 Replies
7. Solaris
Hi,
I am facing issue with one of the drive is solaris 10. it is showing offline in the messages file
scsi: WARNING: /pci@2,600000/QLGC,qlc@0/fp@0,0/ssd@w5006016746e00b1b,0 (ssd0):
drive offline
genunix: WARNING: Page83 data not standards compliant DGC LUNZ 0430
... (1 Reply)
Discussion started by: Prasanth T K
1 Replies
LEARN ABOUT ULTRIX
systemd-fsck
SYSTEMD-FSCK@.SERVICE(8) systemd-fsck@.service SYSTEMD-FSCK@.SERVICE(8)
NAME
systemd-fsck@.service, systemd-fsck-root.service, systemd-fsck - File system checker logic
SYNOPSIS
systemd-fsck@.service
systemd-fsck-root.service
/lib/systemd/systemd-fsck
DESCRIPTION
systemd-fsck@.service and systemd-fsck-root.service are services responsible for file system checks. They are instantiated for each device
that is configured for file system checking. systemd-fsck-root.service is responsible for file system checks on the root file system, but
only if the root filesystem was not checked in the initramfs. systemd-fsck@.service is used for all other file systems and for the root
file system in the initramfs.
These services are started at boot if passno in /etc/fstab for the file system is set to a value greater than zero. The file system check
for root is performed before the other file systems. Other file systems may be checked in parallel, except when they are on the same
rotating disk.
systemd-fsck does not know any details about specific filesystems, and simply executes file system checkers specific to each filesystem
type (/sbin/fsck.*). This helper will decide if the filesystem should actually be checked based on the time since last check, number of
mounts, unclean unmount, etc.
If a file system check fails for a service without nofail, emergency mode is activated, by isolating to emergency.target.
KERNEL COMMAND LINE
systemd-fsck understands these kernel command line parameters:
fsck.mode=
One of "auto", "force", "skip". Controls the mode of operation. The default is "auto", and ensures that file system checks are done
when the file system checker deems them necessary. "force" unconditionally results in full file system checks. "skip" skips any file
system checks.
fsck.repair=
One of "preen", "yes", "no". Controls the mode of operation. The default is "preen", and will automatically repair problems that can be
safely fixed. "yes" will answer yes to all questions by fsck and "no" will answer no to all questions.
SEE ALSO
systemd(1), fsck(8), systemd-quotacheck.service(8), fsck.btrfs(8), fsck.cramfs(8), fsck.ext4(8), fsck.fat(8), fsck.hfsplus(8),
fsck.minix(8), fsck.ntfs(8), fsck.xfs(8)
systemd 237 SYSTEMD-FSCK@.SERVICE(8)