09-29-2009
9 More Discussions You Might Find Interesting
1. Programming
Hello there,
My mulithreaded application (which is too large to represent the source code here) is crashing after installing FreeBSD 7.1-RELEASE/amd64.
It worked properly on others machines (Dual Cores with 4GB of RAM - FreeBSD 6.2-RELEASE/i386).
The current machine has 2x Core 2 Duo... (1 Reply)
Discussion started by: Seenquev
1 Replies
2. Programming
I am developing a Network Appliation to monitor computers in a network.
Specs are
App monitors the current web page viewed in each system
App also can shutdown the computer in the network
App can show all process run by each computer in the network
I am now confused how to start my... (2 Replies)
Discussion started by: valaparambil88
2 Replies
3. IP Networking
hello i have a ubuntu ssh server that i can acess from any of my comnputers but only if they are on the same wireless network as the server. i tested trhis my tehtehring my samsung blackjack to my windows partition and installing openssh to windows it works when windows is on the wireless but no... (1 Reply)
Discussion started by: old noob
1 Replies
4. AIX
Hi All,
Please let me know the command to restart the network interface and enable it on boot in AIX, similar to /etc/init.d/network restart in Redhat.
Thanks,
Sunil.K
please watch out to post in the right subforum! (9 Replies)
Discussion started by: sunilrk07
9 Replies
5. IP Networking
Hello,
I'm attempting to setup a test network with a client-server based architecture using a proprietary application. The client works by communicating with the server on separate links (typically cellular connections) and then initiates a tunnel over each active link. However, in place of the... (0 Replies)
Discussion started by: shadyuk
0 Replies
6. Red Hat
Hi,
I have 2 machines in production environment:
1. redhat machine for application
2. DB machine (oracle)
The application doing a lot of small read&writes from and to the DB machine.
The problem is that after some few hours the network from the application to the DB becomes very slow and... (4 Replies)
Discussion started by: moshesa
4 Replies
7. IP Networking
My son does homework on a school laptop. I was thinking about setting up a gateway on my home network, so that I can monitor web traffic and know if he is doing his homework without standing over his shoulder. Ideally I would like to use the Raspberry Pi Model b that I already have. However, I... (15 Replies)
Discussion started by: gandolf989
15 Replies
8. Solaris
Hi all,
First post here. Working on Solaris 10, on a Sun t4-4, need to change RX queue depth(ethernet, not HBA) and was wondering if i could get by with just restarting the network or if i should just bounce the whole shebang.
Apologies if i missed a similar thread. if there is one, please... (2 Replies)
Discussion started by: caspnx
2 Replies
9. Debian
Hello,
I would like to do follow steps.
Set a static IP-Adress on eth0 (For Testing)
Set DHCP on eth0
All steps should be done without a single reboot.
/etc/network/interfaces
iface eth0 inet static
address 192.0.2.7/24
gateway 192.0.2.254How do i perform... (3 Replies)
Discussion started by: int3g3r
3 Replies
LEARN ABOUT MOJAVE
httppower
httppower(8) powerman httppower(8)
NAME
httppower - communicate with HTTP based power distribution units
SYNOPSIS
httppower [--url URL]
DESCRIPTION
httppower is a helper program for powerman which enables it to communicate with HTTP based power distribution units. It is run interac-
tively by the powerman daemon.
OPTIONS
-u, --url URL
Set the base URL.
INTERACTIVE COMMANDS
The following commands are accepted at the httppower> prompt:
auth user:pass
Authenticate to the base URL with specified user and password, using ``basic'' HTTP authentication which sends the user and password
over the network in plain text.
seturl URL
Set the base URL. Overrides the command line option.
get [URL-suffix]
Send an HTTP GET to the base URL with the optional URL-suffix appended.
post [URL-suffix] key=val[&key=val]...
Send an HTTP POST to the base URL with the optional URL-suffix appended, and key-value pairs as argument.
FILES
/usr/sbin/httppower
/etc/powerman/powerman.conf
ORIGIN
PowerMan was originally developed by Andrew Uselton on LLNL's Linux clusters. This software is open source and distributed under the terms
of the GNU GPL.
SEE ALSO
powerman(1), powermand(8), httppower(8), plmpower(8), vpcd(8), powerman.conf(5), powerman.dev(5), powerman-devices(7).
http://sourceforge.net/projects/powerman
powerman-2.3.5 2009-02-09 httppower(8)