09-29-2009
9 More Discussions You Might Find Interesting
1. Programming
Hello there,
My mulithreaded application (which is too large to represent the source code here) is crashing after installing FreeBSD 7.1-RELEASE/amd64.
It worked properly on others machines (Dual Cores with 4GB of RAM - FreeBSD 6.2-RELEASE/i386).
The current machine has 2x Core 2 Duo... (1 Reply)
Discussion started by: Seenquev
1 Replies
2. Programming
I am developing a Network Appliation to monitor computers in a network.
Specs are
App monitors the current web page viewed in each system
App also can shutdown the computer in the network
App can show all process run by each computer in the network
I am now confused how to start my... (2 Replies)
Discussion started by: valaparambil88
2 Replies
3. IP Networking
hello i have a ubuntu ssh server that i can acess from any of my comnputers but only if they are on the same wireless network as the server. i tested trhis my tehtehring my samsung blackjack to my windows partition and installing openssh to windows it works when windows is on the wireless but no... (1 Reply)
Discussion started by: old noob
1 Replies
4. AIX
Hi All,
Please let me know the command to restart the network interface and enable it on boot in AIX, similar to /etc/init.d/network restart in Redhat.
Thanks,
Sunil.K
please watch out to post in the right subforum! (9 Replies)
Discussion started by: sunilrk07
9 Replies
5. IP Networking
Hello,
I'm attempting to setup a test network with a client-server based architecture using a proprietary application. The client works by communicating with the server on separate links (typically cellular connections) and then initiates a tunnel over each active link. However, in place of the... (0 Replies)
Discussion started by: shadyuk
0 Replies
6. Red Hat
Hi,
I have 2 machines in production environment:
1. redhat machine for application
2. DB machine (oracle)
The application doing a lot of small read&writes from and to the DB machine.
The problem is that after some few hours the network from the application to the DB becomes very slow and... (4 Replies)
Discussion started by: moshesa
4 Replies
7. IP Networking
My son does homework on a school laptop. I was thinking about setting up a gateway on my home network, so that I can monitor web traffic and know if he is doing his homework without standing over his shoulder. Ideally I would like to use the Raspberry Pi Model b that I already have. However, I... (15 Replies)
Discussion started by: gandolf989
15 Replies
8. Solaris
Hi all,
First post here. Working on Solaris 10, on a Sun t4-4, need to change RX queue depth(ethernet, not HBA) and was wondering if i could get by with just restarting the network or if i should just bounce the whole shebang.
Apologies if i missed a similar thread. if there is one, please... (2 Replies)
Discussion started by: caspnx
2 Replies
9. Debian
Hello,
I would like to do follow steps.
Set a static IP-Adress on eth0 (For Testing)
Set DHCP on eth0
All steps should be done without a single reboot.
/etc/network/interfaces
iface eth0 inet static
address 192.0.2.7/24
gateway 192.0.2.254How do i perform... (3 Replies)
Discussion started by: int3g3r
3 Replies
LEARN ABOUT OSF1
ip6_setup
ip6_setup(8) System Manager's Manual ip6_setup(8)
NAME
ip6_setup - IPv6 configuration program
SYNOPSIS
/usr/sbin/ip6_setup
DESCRIPTION
The ip6_setup utility allows you to configure the IPv6 networking software on your system.
To run ip6_setup, enter the following command and then answer the questions: # ip6_setup
You must know your Internet Protocol Version 6 (IPv6) address. If your network uses subnet routing, you must know the subnet mask for your
network. The network manager should be able to provide you with the information that you need.
After the ip6_setup command completes, the network services on the system can be restarted manually with the following command: #
/usr/sbin/rcinet restart
Before you restart the network services with the preceding command, warn the users that the network services on the system are being
removed. File systems that were not mounted using the /etc/fstab file or the automount command must be unmounted with the unmount command.
You must remount these file systems using the mount command after the network is started on your system.
Alternatively, you can reboot the system with the following command: # /usr/sbin/shutdown -r now
FILES
Specifies the host name file. Specifies the environment variables that define the network configuration on your system. Specifies the
trusted hosts file. Specifies the network name file. Specifies Internet routing information. Specifies Internet routing information.
SEE ALSO
Commands: mount(8), rcinet(8)
Files: gateways(4), hosts(4), hosts.equiv(4), networks(4), routes(4).
Network Administration
ip6_setup(8)