09-29-2009
My first guess would be a disk full or corrupted.
9 More Discussions You Might Find Interesting
1. Solaris
Hi All ,
I try to install some packages in my global zone...
On the execution of the installion of the script it quits by saying the error
"Non global zone check failed"
Kindly help me in this regard
Thanks in advance,
jeganr (7 Replies)
Discussion started by: jegaraman
7 Replies
2. Solaris
I have a T5220 running Solaris 10. I have a application that can only run on Solaris 9. I want to build a branded Solaris 9 zone for this application on the Solaris 10 Server.
What steps would I need to accomplish this? (2 Replies)
Discussion started by: soupbone38
2 Replies
3. Solaris
Hi everyone!
I am in dire need to know what are the differences between a solaris zone and a solaris container.. Explanations over the net are very confusing. Please help. Thanks! (8 Replies)
Discussion started by: arah
8 Replies
4. Solaris
Hi,
A quick question: Can Solaris 10 local zones be moved to a Solaris 11 global zone and work well?
Thank you in advance! (5 Replies)
Discussion started by: aixlover
5 Replies
5. UNIX for Advanced & Expert Users
Dear all,
recently, I migrated a solaris zone from one host to another. The zone was inside of a zpool. The zpool cotains two volumes.
I did the following:
host1:
$ zlogin zone1 shutdown -y -g0 -i0 #Zone status changes from running to installed
$ zpool export zone1
host2:
$ zpool... (2 Replies)
Discussion started by: custos
2 Replies
6. Solaris
Hi Gurus
I am not able to find the patching procedure for solaris 10 ( sol10 u11) to latest patchset with sun cluster having failover zones so that same I should follow.
Take an instance, there are sol1 and sol2 nodes and having two failover zones like sozone1-rg and sozone2-rg and currently... (1 Reply)
Discussion started by: nick101
1 Replies
7. Solaris
I am planning to do solaris 11 global zone patching having solaris 10 branded zone. I have a doubts on step 8 specially
Can someone clear my step 8 doubts or if anything wrong between step 1 to step 9 please correct that also as I have pretty good idea about Step 10 mean patching in solaris 10... (2 Replies)
Discussion started by: amity
2 Replies
8. Solaris
I want to migrate a solaris 10 os to solaris 11.4 zone.
I did this
a)Collect some data like id sysid,disks,ip,etc..on solaris10
OK
b)Create this file.cfg with this command on solaris 10
zonep2vchk -c > /migration/sol10.cfg
OK
c)Create the archive flash on Solaris10 (1 Reply)
Discussion started by: Linusolaradm1
1 Replies
9. Solaris
Hi, hoping someone can help, its been a while since I used Solaris.
After creating a NGZ (non global zone), the NGZ can access the GZ (Global Zone) and the GZ can access the NGZ (using ssh, zlogin)
However, the NGZ cannot access any other netwqork devices, it can't even see the default router
... (2 Replies)
Discussion started by: GazinLincoln
2 Replies
LEARN ABOUT DEBIAN
scrounge-ntfs
scrounge-ntfs(8) BSD System Manager's Manual scrounge-ntfs(8)
NAME
scrounge-ntfs -- helps retrieve data from corrupted NTFS partitions
SYNOPSIS
scrounge-ntfs -l disk
scrounge-ntfs -s disk
scrounge-ntfs [-m mftoffset] [-c clustersize] [-o outdir] disk start end
DESCRIPTION
scrounge-ntfs is a utility that can rescue data from corrupted NTFS partitions. It writes the files retrieved to another working file system.
Certain information about the partition needs to be known in advance.
The -l mode is meant to be run in advance of the data corruption, with the output stored away in a file. This allows scrounge-ntfs to recover
data reliably. See the 'NOTES' section below for recover info when this isn't the case.
OPTIONS
The options are as follows:
-c The cluster size (in sectors). When not specified a default of 8 is used.
-l List partition information for a drive. This will only work when the partition table for the given drive is intact.
-m When recovering data this specifies the location of the MFT from the beginning of the partition (in sectors). If not specified
then no directory information can be used, that is, all rescued files will be written to the same directory.
-o Directory to put rescued files in. If not specified then files will be placed in the current directory.
-s Search disk for partition information. (Not implemented yet).
disk The raw device used to access the disk which contains the NTFS partition to rescue files from. eg: '/dev/hdc'
start The beginning of the NTFS partition (in sectors).
end The end of the NTFS partition (in sectors)
NOTES
If you plan on using this program sucessfully you should prepare in advance by storing a copy of the partition information. Use the -l option
to do this. Eventually searching for disk partition information will be implemented, which will solve this problem.
When only one partition exists on a disk or you want to rescue the first partition there are ways to guess at the sector sizes and MFT loca-
tion. See the scrounge-ntfs web page for more info:
http://memberwebs.com/swalter/software/scrounge/
AUTHOR
Stef Walter <stef@memberwebs.com>
scrounge-ntfs June 1, 2019 scrounge-ntfs